Home/Optical transceivers/400G QSFP-DD LR4

WincoTek 400G QSFP-DD LR4 10 km Transceiver(WTQD400-LR4)

WTQD400-LR4 is a 400G QSFP-DD LR4 transceiver for single-mode links up to 10 km. It multiplexes four 53.125 GBd PAM4 lanes onto one duplex LC fiber pair and connects to the host over an eight-lane 400GAUI-8 interface. Typical uses are data center interconnects, campus links and HPC networks where only one fiber pair is available.

WincoTek 400G QSFP-DD LR4 transceiver
Data rate
400 Gb/s
Reach
10 km SMF
Optics
LAN-WDM ×4
Connector
Duplex LC
Key specifications

400G QSFP-DD LR4 at a glance.

Main optical, electrical and environmental values for WTQD400-LR4.

ParameterValue
Ordering codeWTQD400-LR4: 400G-LR4 QSFP-DD 10 km single-mode fiber transceiver, 0 to 70 °C
Data rate4 × 106.25 Gb/s (53.125 GBd PAM4) optical lanes
Standards400G-LR4; 400GAUI-8 (8 × 26.5625 GBd PAM4) electrical; QSFP-DD MSA
WavelengthsLAN-WDM, 4 lanes
TX power, each lane (avg.)−2.7 to 5.1 dBm; total average launch power 11.1 dBm max.
RX sensitivity (OMAouter), each lane−6.8 dBm for TECQ < 1.4 dB; −8.2 + TECQ for 1.4 ≤ TECQ ≤ 3.9 dB; stressed sensitivity −4.3 dBm
RX average receive power, each lane−9 to 5.1 dBm; optical receiver input 6.1 dBm absolute max.
ReachUp to 10 km on single-mode fiber
ConnectorDuplex LC
Power<12 W
Supply3.135 to 3.465 V
Case temperature0 to 70 °C
ManagementCMIS 4.0 management interface

Main values for WTQD400-LR4. Full WincoTek datasheet: DatasheetPDF

Typical applications

Where it is used.

From the datasheet application list and common network use.

  • Data center interconnect (DCI) between buildings up to 10 km
  • Campus and metro edge 400G links on one fiber pair
  • High-performance computing interconnects
  • Cloud network core and aggregation links
Selection notes

Will a 10 km link close?

Work out the link loss before you choose the optic.

Count every loss on the path: fiber attenuation, each connector and each splice. Then keep at least 3 dB of margin for bends, repairs and ageing. The result is the link attenuation the optic has to cover.

If the span is already built, measure it: a light source at one end, a power meter at the other, loss is the difference. Check both directions against the datasheet values: transmitter power minus link loss and margin must land between receiver sensitivity and the maximum receive power.

LR4 runs on one duplex LC pair. If you have parallel single-mode fiber and want to break out to 100G, the 4×LR1 type (WTQD400-DR4-10) is the alternative; for 2 km or less, FR4 is enough.

How it compares

Related WincoTek models.

400G single-mode options. FR4, LR4 and ER4 use one duplex LC pair; DR4 and 4×LR1 use parallel MPO-12 and can break out.

ModelForm factorReachOpticsConnectorMax. power
WTQD400-FR4
DatasheetPDF
QSFP-DD2 km4 lanes at 1310 nmDuplex LC<12 W
WTQD400-LR4
this page
DatasheetPDF
QSFP-DD10 kmLAN-WDM, 4 lanesDuplex LC<12 W
WTQD400-ER4
DatasheetPDF
QSFP-DD40 kmLAN-WDM, 4 lanesDuplex LC12 W max.
WTQD400-DR4-10
DatasheetPDF
QSFP-DD10 km4 parallel lanes (4×LR1)MPO-12 (APC)<8 W
WTQD400-DR4
DatasheetPDF
QSFP-DD500 m4 parallel lanesMPO-12 (APC)8 W (datasheet target)
WTQ112400-DR4-500C
DatasheetPDF
QSFP112500 m4 parallel lanes, 1310 nmMPO-12 (APC)<12 W

Full range and all datasheets: optical transceivers. Guide: 400G DR4 vs FR4 vs LR4: which to choose.

Coding, quality, warranty

Coded to your host, tested first.

Host vendor names describe the target platform only.

Coding & compatibility

WTQD400-LR4 is coded for the host platform you name, for example Cisco, Juniper, Huawei, Arista, Nokia switches and routers. We read and back up the module data, write the approved profile, then read back and verify it with DDM. Compatibility is validated per host model and software release, so we recommend testing coded samples on your equipment before a volume order.

Quality & warranty

Built in ISO 9001-certified manufacturing partners. CE, RoHS, FCC and TÜV test reports are available for each model on request.

Warranty: hardware 3 years, software 1 year.

FAQ

Questions on this model.

Not answered here? Email waley@wincoteknetwork.com or message us on WhatsApp.

What fiber and connector does WTQD400-LR4 use?

Single-mode fiber with a duplex LC connector. Four LAN-WDM lanes are multiplexed onto one fiber pair.

How does LR4 differ from FR4 and 4×LR1?

FR4 (WTQD400-FR4) also uses one duplex LC pair but reaches 2 km. 4×LR1 (WTQD400-DR4-10) reaches 10 km on parallel MPO-12 fiber and can break out to four 100G links. LR4 gives 10 km on one duplex pair.

What power and management interface does it have?

Under 12 W, 0 to 70 °C case temperature, with a CMIS 4.0 management interface.

How do I check my link loss budget?

Add fiber, connector and splice losses, keep at least 3 dB margin, and check that transmitter power minus that total stays between the receiver sensitivity and the maximum receive power in the datasheet, in both directions.

Can WTQD400-LR4 be coded for our switches?

Yes. WTQD400-LR4 is coded for the host platform you name, then read back and verified. Compatibility is validated per host model and software release, so test coded samples before a volume order.

Request a quote for WTQD400-LR4.

Send the host model and software release, quantity and coding needs. We reply with a matched P/N and sample plan.

Email waley@wincoteknetwork.com · WhatsApp / phone +86 176 8896 6828

WhatsApp