Home/Optical transceivers/400G QSFP-DD DR4

WincoTek 400G QSFP-DD DR4 500 m Transceiver(WTQD400-DR4)

WTQD400-DR4 is a 400G QSFP-DD DR4 transceiver for links up to 500 m over parallel single-mode fiber. It runs four 106.25 Gb/s PAM4 lanes in the 1304.5 to 1317.5 nm band on an MPO-12 connector with 8° angled end-face. It works as one 400GBASE-DR4 port or breaks out to four 100GBASE-DR links in data center fabrics.

WincoTek 400G QSFP-DD DR4 transceiver
Data rate
400 Gb/s
Reach
500 m SMF
Breakout
4 × 100G DR
Connector
MPO-12 APC
Key specifications

400G QSFP-DD DR4 at a glance.

Main optical, electrical and environmental values for WTQD400-DR4.

ParameterValue
Ordering codeWTQD400-DR4: 400G-DR4 QSFP-DD 500 m single-mode fiber transceiver, 0 to 70 °C
Data rate4 × 106.25 Gb/s (53.125 GBd PAM4) optical lanes
ModesAggregation: 400GBASE-DR4, 400GAUI-8 (8 × 26.5625 GBd PAM4) · Breakout: 4 × 100GBASE-DR, 100GAUI-2
Standards400GBASE-DR4 compliant; QSFP-DD MSA compliant
Wavelength1304.5 to 1317.5 nm, each lane
TX power, each lane (avg.)−2.9 to 4.0 dBm; OMAouter −0.8 to 4.2 dBm
RX sensitivity (OMAouter), each laneMax(−3.9, SECQ − 5.3) dBm; stressed sensitivity −1.9 dBm
RX average receive power, each lane−5.9 to 4.0 dBm; optical receiver input 5.0 dBm absolute max.
Reach500 m on single-mode fiber
ConnectorMPO-12 with 8° angled end-face
Power consumption8 W (stated as target value in the datasheet)
Case temperature0 to 70 °C
Supply3.135 to 3.465 V; steady-state current 2551.8 mA

Main values for WTQD400-DR4. Full WincoTek datasheet: DatasheetPDF The datasheet does not list a DDM table for this model; ask us for the diagnostics map if you need it.

Typical applications

Where it is used.

From the datasheet application list and common network use.

  • Data center 400GE links up to 500 m on single-mode fiber
  • 400GE to 4 × 100GE breakout over 500 m
  • Switch and router interconnections in leaf-spine fabrics
How it compares

Related WincoTek models.

400G QSFP-DD single-mode options. DR4 and 4×LR1 break out to 4×100G; FR4 and LR4 run on one duplex LC pair.

ModelTypeReachOpticsConnectorMax. power
WTQD400-DR4
this page
DatasheetPDF
400G DR4 (4×100G DR breakout)500 m4 parallel lanes, 1304.5–1317.5 nmMPO-12, 8° angled (APC)8 W (datasheet target)
WTQD400-FR4
DatasheetPDF
400GBASE-FR42 km4 lanes at 1310 nm on one fiber pairDuplex LC<12 W
WTQD400-DR4-10
DatasheetPDF
4×100GBASE-LR1 (breakout)10 km4 parallel lanes, 1304.5–1317.5 nmMPO-12 (APC)<8 W
WTQD400-LR4
DatasheetPDF
400G-LR410 kmLAN-WDMDuplex LC<12 W

Full range and all datasheets: optical transceivers.

Coding, quality, warranty

Coded to your host, tested first.

Host vendor names describe the target platform only.

Coding & compatibility

WTQD400-DR4 is coded for the host platform you name, for example Cisco, Juniper, Huawei, Arista, Nokia switches and routers. We read and back up the module data, write the approved profile, then read back and verify it with DDM. Compatibility is validated per host model and software release, so we recommend testing coded samples on your equipment before a volume order.

Quality & warranty

Built in ISO 9001-certified manufacturing partners. CE, RoHS, FCC and TÜV test reports are available for each model on request.

Warranty: hardware 3 years, software 1 year.

FAQ

Questions on this model.

Not answered here? Email waley@wincoteknetwork.com or message us on WhatsApp.

Can WTQD400-DR4 break out to 4×100G?

Yes. In breakout mode it runs as four 100GBASE-DR links (100GAUI-2 each), for example to four 100G DR ports over an MPO-12 to 4× duplex LC breakout cable.

Which connector and fiber does it need?

An MPO-12 connector with an 8° angled (APC) end-face on single-mode fiber. Use APC MPO trunks or breakout cables.

How does DR4 differ from FR4?

DR4 uses four parallel fibers in each direction for up to 500 m and supports breakout. FR4 (WTQD400-FR4) runs four 1310 nm lanes on one duplex LC pair for up to 2 km.

What power and temperature apply?

The datasheet gives 8 W power consumption as a target value and a 0 to 70 °C case temperature.

Can it be coded for our host?

Yes. WTQD400-DR4 is coded for the host platform you name and verified before shipping. Test coded samples before a volume order.

Request a quote for WTQD400-DR4.

Send the host model and software release, quantity and coding needs. We reply with a matched P/N and sample plan.

Email waley@wincoteknetwork.com · WhatsApp / phone +86 176 8896 6828

WhatsApp