Home/About/Quality & service

Tested before it ships.Backed after delivery.

Every order runs through the same controls: matched and coded to your host, tested before release, labelled and packed to an approved specification, and supported after delivery.

WincoTek QSFP optical transceiver
Production
ISO 9001 partners
Test reports
CE · RoHS · FCC · TÜV
Before volume
Samples & POC
Warranty
HW 3 yr · SW 1 yr
Standards & test reports

Documented for every model.

Ask for the reports for the exact part numbers you are ordering.

Production and compliance

Built in ISO 9001-certified manufacturing partners. CE, RoHS, FCC and TÜV test reports are available for each model on request.

ISO 9001 productionCERoHSFCCTÜV

What we send

  • Test reports for the models in your quotation
  • Datasheets in the unified WincoTek format
  • Sample approval reference kept with the order
Testing

Checked at each line, before it leaves.

Each product line has its own test routine, run at its manufacturing base and recorded against the order.

Optical transceivers

Coded, read back, measured

DDM, optical power, sensitivity and wavelength checks, with serial-number-level test records when the project requires them.

Transceivers →
Data center

Factory acceptance testing

Incoming, in-process and system inspection, then factory acceptance testing (FAT) of the integrated power, cooling and monitoring before release.

Delivery process →
FTTx passives

Every termination tested

Microscopic end-face inspection and testing of every termination; patch cords manufactured and tested to TIA-604 (FOCIS) and IEC 61754.

Patch cords →
Coding & compatibility

Coded for your host. Confirmed on it.

We code supported modules to the required host profile, read back every write and confirm operation on the target equipment.

01

Read & back up

Module identity and EEPROM read; original data saved before coding.

02

Program

The approved coding profile for your host platform is applied.

03

Read back

Programmed data and DDM verified after writing.

04

Validate

Operation confirmed on the target host before volume supply.

Validated per model and firmware; send your host list to confirm before ordering.

Samples & POC

Test on your host, then order.

Start with a focused product list and one representative host configuration. Sample scope and test criteria are agreed before testing begins.

01

Send your host list

Device model, software version, port type and the modules you need.

02

Coded samples

We match part numbers and code identified samples to your host profile.

03

Test on your host

You test against the agreed criteria; logs and any issues are reviewed together.

04

Order

Confirmed part numbers, coding, quantity and quotation for supply.

The approved configuration is recorded against the host and software you tested with. A different host, software release or material product change may require another evaluation.

Labels & packing

Artwork and packing, approved per order.

Product labels, packing and master cartons are confirmed against the order before production, with the same part number across quotation, artwork and packing list.

Product label

  • Brand and part number: WincoTek or the agreed customer brand; exact product code and revision
  • Technical text: consistent with the datasheet
  • Barcode and serial: agreed symbology and serial format, without duplicates

Packing and carton

  • Unit packing: ESD protection and dust caps
  • Traceability: serial or lot on inner packing
  • Carton label: order reference, part number, quantity, carton number, gross / net weight
Warranty & RMA

Hardware 3 years. Software 1 year.

Coverage, remedies and RMA terms for each order follow the quotation or contract. Support starts with remote troubleshooting.

Warranty

Covered under normal use within the specified operating conditions.

3years

Hardware

1year

Software

Not covered

  • Damage from improper handling or use
  • Operation outside the temperature range in the product specification
  • Removed or broken serial labels
  • Disassembly or repair by unauthorised parties
01

Contact us

Order reference, part and serial number, fault description, when first observed, quantity affected.

02

Remote troubleshooting

Host model and software version, alarms, module diagnostics, port configuration and test logs.

03

RMA authorisation

Request an RMA reference before shipping any unit back.

04

Return & review

Original labels intact, optical ports capped, ESD packing, RMA reference quoted.

An RMA request or number does not by itself confirm warranty eligibility or a repair outcome. RMA details →

Support & training

Support sized to your network.

From a single module question to a service agreement for a whole network build.

Technical support

Engineers who know the products

Send the host, alarms, diagnostics and test logs; we work through the issue with you remotely first.

Email support →
Service programs

Agreements tailored to you

Service agreements sized to your network environment and business goals, defined in the quotation or contract.

Ask about service →
Training

Standard or custom courses

Courses to operate, maintain and troubleshoot your optical systems, delivered at our facility or at your site.

Ask about training →

Need test reports, samples or an RMA?

Send the part numbers or order reference and what you need. One inbox handles all three.

WhatsApp