Home/Optical transceivers/400G QSFP-DD ER4

WincoTek 400G QSFP-DD ER4 40 km Transceiver(WTQD400-ER4)

WTQD400-ER4 is a 400G QSFP-DD ER4 transceiver for single-mode links up to 40 km. Four 106.25 Gb/s PAM4 lanes from EML lasers sit on a LAN-WDM grid around 1310 nm and share one duplex LC fiber pair. It is used for 400GBASE-ER4 links in 5G backhaul, metro data center interconnect and cloud networks.

WincoTek 400G QSFP-DD ER4 transceiver
Data rate
425 Gb/s
Reach
40 km SMF
Optics
LAN-WDM, EML
Connector
Duplex LC
Key specifications

400G QSFP-DD ER4 at a glance.

Main optical, electrical and environmental values for WTQD400-ER4.

ParameterValue
Ordering codeWTQD400-ER4: 425 Gb/s, EML, SMF, 40 km, LC, 0 to 70 °C, with DDM
Data rate4 × 106.25 Gb/s optical lanes (53.125 GBd PAM4); 400GAUI-8 electrical interface, 8 lanes
Application400GBASE-ER4 Ethernet; 5G backhaul, data center and cloud
WavelengthsLAN-WDM, 4 lanes: 1304.58 / 1306.85 / 1309.14 / 1311 nm (typ.)
TX power, each lane (avg.)1.5 to 7.1 dBm; total average launch power 10 dBm max.; OMAouter 4.5 to 7.9 dBm
RX sensitivity (OMAouter), each lane−14 dBm
RX average receive power, each lane−16.2 to −3.4 dBm; damage threshold −2.4 dBm
Bit error ratioPre-FEC 2.4 × 10−4 max.; post-FEC 1 × 10−12 max.
ReachUp to 40 km on single-mode fiber
ConnectorDuplex LC
Power12 W max.; single +3.3 V supply
Case temperature0 to 70 °C
DDMYes: temperature, voltage, TX bias, TX power and RX power per lane, over I²C
EnvironmentalComplies with EU Directive 2015/863/EU

Main values for WTQD400-ER4. Full WincoTek datasheet: DatasheetPDF

Short links and testing. The transmitter launches up to 7.1 dBm per lane, while average receive power must stay at or below −3.4 dBm per lane (damage threshold −2.4 dBm). On short spans and in loop-back tests, check RX power in DDM and add an LC attenuator so each lane stays inside −16.2 to −3.4 dBm.
Typical applications

Where it is used.

From the datasheet application list and common network use.

  • 400GBASE-ER4 links up to 40 km
  • 5G backhaul and metro aggregation
  • Data center interconnect between sites over dark fiber
  • Cloud network links where a DWDM system is not justified
Selection notes

40 km at 1310 nm.

Loss, FEC and receive power on an ER4 link.

Fiber loss per kilometre is higher around 1310 nm than at 1550 nm, so at 40 km the fiber itself takes most of the budget. Measure the span, add connector and splice losses, and keep at least 3 dB of margin before you commit.

The datasheet specifies the link at a pre-FEC bit error ratio of 2.4 × 10⁻⁴ and a post-FEC ratio of 1 × 10⁻¹², so the host FEC is part of the design. Keep it enabled on both ends.

Too much light is as harmful as too little: on short spans the receiver can be overloaded. Read RX power in DDM after installation and attenuate where needed.

How it compares

Related WincoTek models.

400G single-mode options. ER4 extends the duplex LC family to 40 km.

ModelForm factorReachOpticsConnectorMax. power
WTQD400-FR4
DatasheetPDF
QSFP-DD2 km4 lanes at 1310 nmDuplex LC<12 W
WTQD400-LR4
DatasheetPDF
QSFP-DD10 kmLAN-WDM, 4 lanesDuplex LC<12 W
WTQD400-ER4
this page
DatasheetPDF
QSFP-DD40 kmLAN-WDM, 4 lanesDuplex LC12 W max.
WTQD400-DR4-10
DatasheetPDF
QSFP-DD10 km4 parallel lanes (4×LR1)MPO-12 (APC)<8 W
WTQD400-DR4
DatasheetPDF
QSFP-DD500 m4 parallel lanesMPO-12 (APC)8 W (datasheet target)
WTQ112400-DR4-500C
DatasheetPDF
QSFP112500 m4 parallel lanes, 1310 nmMPO-12 (APC)<12 W

Full range and all datasheets: optical transceivers. Guide: 400G DR4 vs FR4 vs LR4: which to choose.

Coding, quality, warranty

Coded to your host, tested first.

Host vendor names describe the target platform only.

Coding & compatibility

WTQD400-ER4 is coded for the host platform you name, for example Cisco, Juniper, Huawei, Arista, Nokia switches and routers. We read and back up the module data, write the approved profile, then read back and verify it with DDM. Compatibility is validated per host model and software release, so we recommend testing coded samples on your equipment before a volume order.

Quality & warranty

Built in ISO 9001-certified manufacturing partners. CE, RoHS, FCC and TÜV test reports are available for each model on request.

Warranty: hardware 3 years, software 1 year.

FAQ

Questions on this model.

Not answered here? Email waley@wincoteknetwork.com or message us on WhatsApp.

Do I need an attenuator?

On short spans and in loop-back tests, yes. Each lane launches up to 7.1 dBm, and average receive power must not exceed −3.4 dBm per lane (damage threshold −2.4 dBm).

Does WTQD400-ER4 rely on FEC?

Yes. The datasheet gives a maximum pre-FEC bit error ratio of 2.4 × 10⁻⁴ and a post-FEC ratio of 1 × 10⁻¹², so host FEC must be enabled.

Which wavelengths does it use?

Four lanes on a LAN-WDM grid: 1304.58, 1306.85, 1309.14 and 1311 nm typical, multiplexed onto one duplex LC fiber pair.

What are the power and temperature ratings?

12 W maximum from a single +3.3 V supply, with a 0 to 70 °C case temperature.

Can WTQD400-ER4 be coded for our switches?

Yes. WTQD400-ER4 is coded for the host platform you name, then read back and verified. Compatibility is validated per host model and software release, so test coded samples before a volume order.

Request a quote for WTQD400-ER4.

Send the host model and software release, quantity and coding needs. We reply with a matched P/N and sample plan.

Email waley@wincoteknetwork.com · WhatsApp / phone +86 176 8896 6828

WhatsApp