Home/Optical transceivers/400G QSFP112 DR4

WincoTek 400G QSFP112 DR4 500 m Transceiver(WTQ112400-DR4-500C)

WTQ112400-DR4-500C is a 400G QSFP112 DR4 transceiver for single-mode links up to 500 m. Four 106.25 Gb/s electrical lanes map straight onto four 53.125 GBd PAM4 optical lanes at 1310 nm, on an MPO-12 APC connector. It is built as a silicon photonics design with a DSP inside, and serves 400G Ethernet in data center and cloud networks.

WincoTek 400G QSFP112 DR4 transceiver
Data rate
425 Gb/s
Reach
500 m SMF
Wavelength
1310 nm
Connector
MPO-12 APC
Key specifications

400G QSFP112 DR4 at a glance.

Main optical, electrical and environmental values for WTQ112400-DR4-500C.

ParameterValue
Ordering codeWTQ112400-DR4-500C: 425 Gb/s, 1310 nm, 500 m, SMF, DDM, MPO 1×12 APC, 0 to 70 °C
Data rate425 Gb/s; 4 × 106.25 Gb/s electrical interface; 4 × 53.125 GBd PAM4 optical lanes
Application400G Ethernet; data center and cloud networks
Wavelength1304.5 to 1317.5 nm, each lane
TX power, each lane (avg.)−2.9 to 4 dBm; OMAouter −0.8 to 4.2 dBm
RX sensitivity (OMAouter), each lane−4.4 dBm; stressed sensitivity −1.9 dBm
RX average receive power, each lane−5.9 to 4 dBm; damage threshold +5 dBm
Reach / FECUp to 500 m on single-mode fiber; FEC required on the host
ConnectorMPO-12 (APC)
Power<12 W
Supply3.135 to 3.45 V
Case temperature0 to 70 °C
DDMYes
EnvironmentalRoHS compliant

Main values for WTQ112400-DR4-500C. Full WincoTek datasheet: DatasheetPDF

Typical applications

Where it is used.

From the datasheet application list and common network use.

  • 400G Ethernet switch-to-switch links up to 500 m
  • Leaf-spine fabrics built on 112G-SerDes switches with QSFP112 ports
  • Data center and cloud network interconnects on parallel single-mode fiber
Selection notes

QSFP112 or QSFP-DD?

Same 400G DR4 optics, different host interface.

QSFP112 carries 400G on four electrical lanes of about 100G each, so it fits switches whose ports run 112G SerDes. A QSFP-DD 400G module uses eight 50G lanes in a double-row connector. Check the host port type first: the optical side of both DR4 types is the same four 1310 nm lanes on MPO-12.

The datasheet states that FEC on the host is required to reach 500 m. Enable it on both ends before testing the link.

Use single-mode MPO-12 trunks with APC end-faces. A flat PC connector does not mate correctly with an APC receptacle.

How it compares

Related WincoTek models.

400G DR4-class options by host form factor. For one duplex LC pair instead of parallel fiber, see FR4.

ModelForm factorReachOpticsConnectorMax. power
WTQ112400-DR4-500C
this page
DatasheetPDF
QSFP112500 m4 parallel lanes, 1310 nmMPO-12 (APC)<12 W
WTQD400-DR4
DatasheetPDF
QSFP-DD500 m4 parallel lanesMPO-12 (APC)8 W (datasheet target)
WTOS400-DR4-500C-CM
DatasheetPDF
OSFP500 m1310 nmMPO-12 (APC)<10 W
WTQD400-DR4-10
DatasheetPDF
QSFP-DD10 km4 parallel lanes (4×LR1)MPO-12 (APC)<8 W
WTQD400-FR4
DatasheetPDF
QSFP-DD2 km4 lanes at 1310 nmDuplex LC<12 W

Full range and all datasheets: optical transceivers. Guide: 400G DR4 vs FR4 vs LR4: which to choose.

Coding, quality, warranty

Coded to your host, tested first.

Host vendor names describe the target platform only.

Coding & compatibility

WTQ112400-DR4-500C is coded for the host platform you name, for example Cisco, Juniper, Huawei, Arista, Nokia switches and routers. We read and back up the module data, write the approved profile, then read back and verify it with DDM. Compatibility is validated per host model and software release, so we recommend testing coded samples on your equipment before a volume order.

Quality & warranty

Built in ISO 9001-certified manufacturing partners. CE, RoHS, FCC and TÜV test reports are available for each model on request.

Warranty: hardware 3 years, software 1 year.

FAQ

Questions on this model.

Not answered here? Email waley@wincoteknetwork.com or message us on WhatsApp.

What host port does WTQ112400-DR4-500C need?

A QSFP112 port. The module uses a 4 × 106.25 Gb/s electrical interface, so it is meant for hosts with 112G-class SerDes.

Is FEC required?

Yes. The datasheet notes that FEC on the host system is required to support the maximum 500 m distance.

Which fiber and connector does it use?

Single-mode fiber with an MPO-12 connector with APC end-face. The four lanes run at 1304.5 to 1317.5 nm.

How is it different from the QSFP-DD DR4?

The optics are the same class: four 1310 nm PAM4 lanes up to 500 m on MPO-12 APC. WTQD400-DR4 plugs into QSFP-DD ports with an eight-lane 400GAUI-8 interface; WTQ112400-DR4-500C plugs into QSFP112 ports with four 106.25 Gb/s lanes.

Can WTQ112400-DR4-500C be coded for our switches?

Yes. WTQ112400-DR4-500C is coded for the host platform you name, then read back and verified. Compatibility is validated per host model and software release, so test coded samples before a volume order.

Request a quote for WTQ112400-DR4-500C.

Send the host model and software release, quantity and coding needs. We reply with a matched P/N and sample plan.

Email waley@wincoteknetwork.com · WhatsApp / phone +86 176 8896 6828

WhatsApp