Home/Optical transceivers/100G QSFP28 SR4

WincoTek 100G QSFP28 SR4 100 m Transceiver(WTQ2885P10C1CN1)

WTQ2885P10C1CN1 is a 100G QSFP28 SR4 transceiver for multimode links up to 70 m on OM3 or 100 m on OM4. It runs four independent 25 Gb/s lanes at 850 nm side by side, four fibers in each direction, through one MPO receptacle, and supports aggregate rates from 103.1 to 112.2 Gb/s. It complies with IEEE 802.3bm 100GBASE-SR4 and draws 2.5 W at most.

WincoTek 100G QSFP28 SR4 transceiver
Data rate
103.1–112.2 Gb/s
Reach
70 m OM3 / 100 m OM4
Wavelength
850 nm
Connector
MPO
Key specifications

100G QSFP28 SR4 at a glance.

Main optical, electrical and environmental values for WTQ2885P10C1CN1.

ParameterValue
Ordering codeWTQ2885P10C1CN1: 103.1 / 112.2 Gb/s, 4 × 850 nm, 100 m multimode, 0 to 70 °C
Data rate103.1 to 112.2 Gb/s aggregate; 25.78125 to 28.05 Gb/s per lane
StandardsIEEE 802.3bm 100GBASE-SR4; QSFP28 MSA; 4 × 25G electrical interface (OIF CEI-28G-VSR)
Applications (datasheet)100G Ethernet; 4 × 28G multimode OTN; 128G Fibre Channel; InfiniBand QDR, DDR and SDR
Wavelength840 to 860 nm (850 nm typ.)
TX power, each lane (avg.)−9 to 2.4 dBm; OMA −7.1 to 3.0 dBm
RX sensitivity (OMA), each lane−9.2 dBm at BER 5 × 10−5; stressed sensitivity −5.2 dBm
RX average receive power, each lane−10.9 to 2.4 dBm; damage threshold 3.4 dBm
Bit error ratioPre-FEC 5 × 10−5; post-FEC 1 × 10−12 (host FEC enabled)
Reach70 m on OM3, 100 m on OM4 multimode fiber
ConnectorMPO; four fibers transmit, four receive
Power2.5 W max.; supply current 757 mA max.
Supply3.135 to 3.465 V
Case temperature0 to 70 °C
DDMYes: temperature ±3 °C, supply voltage ±0.15 V, bias per lane ±10%, TX and RX power per lane ±2 dB
EnvironmentalRoHS-6 compliant

Main values for WTQ2885P10C1CN1. Full WincoTek datasheet: DatasheetPDF

Typical applications

Where it is used.

From the datasheet application list and common network use.

  • 100GBASE-SR4 switch-to-switch links inside a data center row or hall
  • Top-of-rack to leaf uplinks up to 100 m on OM4
  • InfiniBand, Fibre Channel and multimode OTN links listed in the datasheet
  • Moving existing parallel multimode cabling from 40G to 100G
Selection notes

SR4 or single-mode 100G?

The fiber in the floor and the connector on the panel decide.

SR4 sends four 25G lanes side by side over eight multimode fibers, so it needs MPO cabling rather than duplex LC. Reach depends on the fiber grade: 70 m on OM3, 100 m on OM4. Measure the longest run, patch cords included, before you settle the cabling grade.

An MPO channel has to match on fiber count, pins (male on one side, female on the other) and polarity. A direct SR4-to-SR4 link usually uses a Type B (full crossover) trunk, so each transmit lane lands on a receive lane at the far end. Check pins, key orientation and polarity on the whole channel before ordering.

For runs over 100 m, or halls cabled with single-mode fiber, a duplex single-mode optic fits better: the 100G QSFP28 LR4 for up to 10 km, or a single-fiber 100G QSFP28 BiDi where fiber is short.

How it compares

Related WincoTek models.

Parallel multimode options from 40G to 400G. Match the MPO type and fiber count already in your patch field.

ModelTypeReach (multimode)ConnectorMax. power
WTQ2885P10C1CN1
this page
DatasheetPDF
100G QSFP28 SR470 m OM3 / 100 m OM4MPO2.5 W
WTQ40SRD
Datasheet on request
40G QSFP+ SR4100 mOn requestOn request
WTQP200-SR4
DatasheetPDF
200G QSFP56 SR470 m OM3 / 100 m OM4MPO-12 (APC)<6 W
WTQ112400-SR4-50C
DatasheetPDF
400G QSFP112 SR450 mMPO-12 (APC)<8 W
WTQD400-SR8-100C
DatasheetPDF
400G QSFP-DD SR8100 m OM4MPO-16 (APC)<12 W

Full range and all datasheets: optical transceivers.

Coding, quality, warranty

Coded to your host, tested first.

Host vendor names describe the target platform only.

Coding & compatibility

WTQ2885P10C1CN1 is coded for the host platform you name, for example Cisco, Juniper, Huawei, Arista, Nokia switches and routers. We read and back up the module data, write the approved profile, then read back and verify it with DDM. Compatibility is validated per host model and software release, so we recommend testing coded samples on your equipment before a volume order.

Quality & warranty

Built in ISO 9001-certified manufacturing partners. CE, RoHS, FCC and TÜV test reports are available for each model on request.

Warranty: hardware 3 years, software 1 year.

FAQ

Questions on this model.

Not answered here? Email waley@wincoteknetwork.com or message us on WhatsApp.

How far does WTQ2885P10C1CN1 reach?

Up to 70 m on OM3 and 100 m on OM4 multimode fiber, per the datasheet.

Which connector and cabling does it need?

An MPO connector on parallel multimode fiber: four fibers transmit and four receive. Match the trunk pin type, key orientation and polarity to the link.

Does it need FEC on the host?

The datasheet specifies the link at a pre-FEC bit error ratio of 5 × 10⁻⁵ and a post-FEC ratio of 1 × 10⁻¹², so keep host FEC enabled on both ends.

What else can it carry besides 100G Ethernet?

The datasheet lists 4 × 28G multimode OTN, 128G Fibre Channel and InfiniBand QDR, DDR and SDR, at aggregate rates from 103.1 to 112.2 Gb/s.

Can WTQ2885P10C1CN1 be coded for our switches?

Yes. WTQ2885P10C1CN1 is coded for the host platform you name, then read back and verified. Compatibility is validated per host model and software release, so test coded samples before a volume order.

Request a quote for WTQ2885P10C1CN1.

Send the host model and software release, quantity and coding needs. We reply with a matched P/N and sample plan.

Email waley@wincoteknetwork.com · WhatsApp / phone +86 176 8896 6828

WhatsApp