Home/Optical transceivers/100G QSFP28 LR4

WincoTek 100G QSFP28 LR4 10 km Transceiver(WTQ1HL1)

WTQ1HL1 is a 100G QSFP28 LR4 transceiver for links up to 10 km over single-mode fiber. It multiplexes four 25.78 Gb/s LAN-WDM lanes onto one duplex LC fiber pair, with EML lasers and a PIN receiver. Use it for 100GBASE-LR4 router, switch and data center links, in commercial (0 to 70 °C) or industrial (−40 to 85 °C) grade.

WincoTek 100G QSFP28 LR4 transceiver
Data rate
103.125 Gb/s
Reach
10 km SMF
Wavelengths
LAN-WDM ×4
Connector
Duplex LC
Key specifications

100G QSFP28 LR4 at a glance.

Main optical, electrical and environmental values for WTQ1HL1.

ParameterValue
Ordering codesWTQ1HL1C (commercial), WTQ1HL1I (industrial)
Data rate103.125 Gb/s aggregate; 4 × 25.78125 Gb/s (NRZ)
Application100GBASE-LR4 Ethernet; 100G datacom and telecom connections
Wavelengths4 LAN-WDM lanes: 1295.56 / 1300.05 / 1304.58 / 1309.14 nm (typ.)
Laser / receiverLAN-WDM EML laser, PIN ROSA
TX power, each lane (avg.)−4.3 to 4.5 dBm; total average launch power 10.5 dBm max.
TX OMA, each lane−1.3 to 4.5 dBm
RX sensitivity (OMA), each lane−8.6 dBm
RX average receive power, each lane−10.6 to 4.5 dBm; damage threshold 5.5 dBm
Reach / FECUp to 10 km with KR4 FEC
Fiber / connector9/125 µm single-mode fiber; duplex LC
Electrical interfaceCAUI-4; I²C two-wire serial interface
Form factorQSFP28 MSA package; single +3.3 V supply
Power dissipation<4 W (WTQ1HL1C); <5 W (WTQ1HL1I)
Case temperature0 to 70 °C (WTQ1HL1C); −40 to 85 °C (WTQ1HL1I)
DDMYes: temperature, voltage, bias current, TX and RX power

Main values for WTQ1HL1. Full WincoTek datasheet: DatasheetPDF

Typical applications

Where it is used.

From the datasheet application list and common network use.

  • 100GBASE-LR4 Ethernet links between routers and switches
  • 100G datacom and telecom connections up to 10 km
  • Data center and campus building-to-building links over single-mode fiber
  • Metro aggregation and core router uplinks
  • Industrial-grade (WTQ1HL1I) for outdoor cabinets and sites without climate control
How it compares

Related WincoTek models.

Same LAN-WDM grid and duplex LC across the three. Choose by span length and received-power range.

ModelReachLaser / receiverTX power, each lane (avg.)RX sensitivity, each laneMax. powerCase temperature
WTQ1HL1
this page
DatasheetPDF
10 kmLAN-WDM EML / PIN−4.3 to 4.5 dBm−8.6 dBm (OMA)<4 W (C) / <5 W (I)0 to 70 °C / −40 to 85 °C
WTQ1HE4
DatasheetPDF
40 kmLAN-WDM EML / PIN−1 to 6.5 dBm−18 dBm (avg.)<5 W (C) / <5.5 W (I)0 to 70 °C / −40 to 85 °C
WTQ1HZ8
DatasheetPDF
80 kmLAN-WDM EML / PIN with SOA1 to 6.5 dBm−27 dBm (avg.)<6 W0 to 70 °C

Full range and all datasheets: optical transceivers.

Coding, quality, warranty

Coded to your host, tested first.

Host vendor names describe the target platform only.

Coding & compatibility

WTQ1HL1 is coded for the host platform you name, for example Cisco, Juniper, Huawei, Arista, Nokia switches and routers. We read and back up the module data, write the approved profile, then read back and verify it with DDM. Compatibility is validated per host model and software release, so we recommend testing coded samples on your equipment before a volume order.

Quality & warranty

Built in ISO 9001-certified manufacturing partners. CE, RoHS, FCC and TÜV test reports are available for each model on request.

Warranty: hardware 3 years, software 1 year.

FAQ

Questions on this model.

Not answered here? Email waley@wincoteknetwork.com or message us on WhatsApp.

What fiber and connector does WTQ1HL1 use?

Single-mode 9/125 µm fiber with a duplex LC connector. The four LAN-WDM lanes (1295.56, 1300.05, 1304.58 and 1309.14 nm typical) are multiplexed onto one fiber pair.

Does the 10 km reach need FEC?

Yes. The datasheet specifies up to 10 km with KR4 FEC, so enable KR4 FEC on the host port.

What is the difference between WTQ1HL1C and WTQ1HL1I?

WTQ1HL1C is commercial grade, 0 to 70 °C case temperature, under 4 W. WTQ1HL1I is industrial grade, −40 to 85 °C, under 5 W.

Should I choose LR4, ER4 or ZR4?

By span: WTQ1HL1 LR4 for up to 10 km, WTQ1HE4 ER4 for up to 40 km and WTQ1HZ8 ZR4 for up to 80 km. Check the received power against each datasheet range.

Can WTQ1HL1 be coded for our switches?

Yes. Modules are coded for the host platform you name, then read back and verified. We recommend testing coded samples on your equipment before a volume order.

Request a quote for WTQ1HL1.

Send the host model and software release, quantity and coding needs. We reply with a matched P/N and sample plan.

Email waley@wincoteknetwork.com · WhatsApp / phone +86 176 8896 6828

WhatsApp