Home/Optical transceivers/100G QSFP28 ER4

WincoTek 100G QSFP28 ER4 40 km Transceiver(WTQ1HE4)

WTQ1HE4 is a 100G QSFP28 ER4 transceiver for links up to 40 km over single-mode fiber. Four 25.78 Gb/s LAN-WDM lanes run on one duplex LC fiber pair, with EML lasers and a PIN receiver rated −18 dBm per lane. It is used for 100GBASE-ER4 metro, aggregation and data center interconnect links.

WincoTek 100G QSFP28 ER4 transceiver
Data rate
103.125 Gb/s
Reach
40 km SMF
Receiver
PIN
Connector
Duplex LC
Key specifications

100G QSFP28 ER4 at a glance.

Main optical, electrical and environmental values for WTQ1HE4.

ParameterValue
Ordering codesWTQ1HE4C (commercial), WTQ1HE4I (industrial)
Data rate103.125 Gb/s aggregate; 4 × 25.78125 Gb/s
Application100GBASE-ER4 Ethernet; 100G datacom and telecom connections
Wavelengths4 LAN-WDM lanes: 1295.56 / 1300.05 / 1304.58 / 1309.14 nm (typ.)
Laser / receiverLAN-WDM EML laser, PIN receiver
TX power, each lane (avg.)−1 to 6.5 dBm; total average launch power 12.5 dBm max.
TX OMA, each lane0 to 6.5 dBm
RX sensitivity (avg.), each lane−18 dBm
RX average receive power, each lane−23 to −3.5 dBm; damage threshold −2.5 dBm
ReachUp to 40 km on single-mode fiber
Fiber / connector9/125 µm single-mode fiber; duplex LC
Electrical interfaceCAUI-4; I²C two-wire serial interface; IntL/RxLOSL and LPMode/TxDIS multi-pin functions
Form factorQSFP28 MSA package; single +3.3 V supply
Power dissipation<5 W (WTQ1HE4C); <5.5 W (WTQ1HE4I)
Case temperature0 to 70 °C (WTQ1HE4C); −40 to 85 °C (WTQ1HE4I)
DDMYes: temperature, voltage, bias current, TX power (−1 to 6.5 dBm), RX power (−23 to −3.5 dBm)

Main values for WTQ1HE4. Full WincoTek datasheet: DatasheetPDF

Short links and testing. The datasheet limits average receive power to −3.5 dBm per lane (damage threshold −2.5 dBm), while the transmitter can launch up to 6.5 dBm per lane. On short spans and in loop-back tests, check RX power in DDM and add an LC attenuator so each lane stays inside −23 to −3.5 dBm.
Typical applications

Where it is used.

From the datasheet application list and common network use.

  • 100GBASE-ER4 Ethernet links up to 40 km
  • Metro aggregation and core router interconnects
  • Data center interconnect (DCI) between sites
  • Carrier backhaul and 5G mid-haul aggregation over dark fiber
  • Industrial-grade (WTQ1HE4I) for outdoor and remote sites
How it compares

Related WincoTek models.

Same LAN-WDM grid and duplex LC across the three. ER4 raises launch power and receiver sensitivity for 40 km.

ModelReachLaser / receiverTX power, each lane (avg.)RX sensitivity, each laneMax. powerCase temperature
WTQ1HL1
DatasheetPDF
10 kmLAN-WDM EML / PIN−4.3 to 4.5 dBm−8.6 dBm (OMA)<4 W (C) / <5 W (I)0 to 70 °C / −40 to 85 °C
WTQ1HE4
this page
DatasheetPDF
40 kmLAN-WDM EML / PIN−1 to 6.5 dBm−18 dBm (avg.)<5 W (C) / <5.5 W (I)0 to 70 °C / −40 to 85 °C
WTQ1HZ8
DatasheetPDF
80 kmLAN-WDM EML / PIN with SOA1 to 6.5 dBm−27 dBm (avg.)<6 W0 to 70 °C

Full range and all datasheets: optical transceivers.

Coding, quality, warranty

Coded to your host, tested first.

Host vendor names describe the target platform only.

Coding & compatibility

WTQ1HE4 is coded for the host platform you name, for example Cisco, Juniper, Huawei, Arista, Nokia switches and routers. We read and back up the module data, write the approved profile, then read back and verify it with DDM. Compatibility is validated per host model and software release, so we recommend testing coded samples on your equipment before a volume order.

Quality & warranty

Built in ISO 9001-certified manufacturing partners. CE, RoHS, FCC and TÜV test reports are available for each model on request.

Warranty: hardware 3 years, software 1 year.

FAQ

Questions on this model.

Not answered here? Email waley@wincoteknetwork.com or message us on WhatsApp.

What receiver does WTQ1HE4 use?

A PIN receiver. The datasheet gives a receiver sensitivity of −18 dBm average per lane and an average receive power range of −23 to −3.5 dBm per lane.

Do I need an attenuator on short links?

Often yes. Average receive power must stay at or below −3.5 dBm per lane (damage threshold −2.5 dBm), and the transmitter launches up to 6.5 dBm per lane. Check RX power in DDM and add an LC attenuator on short spans or loop-back tests.

Which temperature grades are available?

WTQ1HE4C for 0 to 70 °C case temperature (under 5 W) and WTQ1HE4I for −40 to 85 °C (under 5.5 W).

When should I use ZR4 instead of ER4?

When the span is beyond 40 km. WTQ1HZ8 ZR4 reaches up to 80 km with KR4 FEC, using a PIN receiver with SOA.

Can WTQ1HE4 be coded for our routers?

Yes. We code it for the host platform you name, read back and verify the data, and recommend testing coded samples before volume supply.

Request a quote for WTQ1HE4.

Send the host model and software release, quantity and coding needs. We reply with a matched P/N and sample plan.

Email waley@wincoteknetwork.com · WhatsApp / phone +86 176 8896 6828

WhatsApp