Home/Optical transceivers/100G QSFP28 ZR4

WincoTek 100G QSFP28 ZR4 80 km Transceiver(WTQ1HZ8)

WTQ1HZ8 is a 100G QSFP28 ZR4 transceiver for links up to 80 km over single-mode fiber with KR4 FEC. It carries four 25.78 Gb/s LAN-WDM lanes on one duplex LC fiber pair, using EML lasers and a PIN receiver with SOA rated −27 dBm per lane. Typical use is long metro, regional and data center interconnect spans without a DWDM system.

WincoTek 100G QSFP28 ZR4 transceiver
Data rate
103.125 Gb/s
Reach
80 km SMF
Receiver
PIN + SOA
Max. power
6 W
Key specifications

100G QSFP28 ZR4 at a glance.

Main optical, electrical and environmental values for WTQ1HZ8.

ParameterValue
Ordering codeWTQ1HZ8
Data rate103.125 Gb/s aggregate; 4 × 25.78125 Gb/s
Application100GBASE-ZR4 Ethernet; 100G datacom and telecom connections
Wavelengths4 LAN-WDM lanes: 1295.56 / 1300.05 / 1304.58 / 1309.14 nm (typ.)
Laser / receiverLAN-WDM EML laser, PIN receiver with SOA
TX power, each lane (avg.)1 to 6.5 dBm; total launch power 7 to 12.5 dBm
TX OMA, each lane2 to 6.5 dBm
RX sensitivity (avg.), each lane−27 dBm
RX average receive power, each lane−28 to −6 dBm; damage threshold 5.5 dBm
Reach / FECUp to 80 km with KR4 FEC
Fiber / connector9/125 µm single-mode fiber; duplex LC
Electrical interfaceCAUI-4; I²C two-wire serial interface; IntL/RxLOSL and LPMode/TxDIS multi-pin functions
Form factorQSFP28 MSA package; single +3.3 V supply
Power dissipation6 W max.
Case temperature0 to 70 °C
DDMYes: temperature, voltage, bias current, TX and RX power
EnvironmentalComplies with EU Directive 2015/863/EU

Main values for WTQ1HZ8. Full WincoTek datasheet: DatasheetPDF

Short links and testing. The datasheet gives a maximum average receive power of −6 dBm per lane, while the transmitter launches 1 to 6.5 dBm per lane. On spans much shorter than 80 km, and always in loop-back tests, measure RX power in DDM and add an LC attenuator so each lane stays inside −28 to −6 dBm.
Typical applications

Where it is used.

From the datasheet application list and common network use.

  • 100GBASE-ZR4 Ethernet links up to 80 km
  • Long metro and regional router interconnects
  • Data center interconnect (DCI) over dark fiber without DWDM
  • Carrier backbone and aggregation links between exchanges
How it compares

Related WincoTek models.

Same LAN-WDM grid and duplex LC across the three. ZR4 adds an SOA ahead of the PIN receiver for 80 km.

ModelReachLaser / receiverTX power, each lane (avg.)RX sensitivity, each laneMax. powerCase temperature
WTQ1HL1
DatasheetPDF
10 kmLAN-WDM EML / PIN−4.3 to 4.5 dBm−8.6 dBm (OMA)<4 W (C) / <5 W (I)0 to 70 °C / −40 to 85 °C
WTQ1HE4
DatasheetPDF
40 kmLAN-WDM EML / PIN−1 to 6.5 dBm−18 dBm (avg.)<5 W (C) / <5.5 W (I)0 to 70 °C / −40 to 85 °C
WTQ1HZ8
this page
DatasheetPDF
80 kmLAN-WDM EML / PIN with SOA1 to 6.5 dBm−27 dBm (avg.)<6 W0 to 70 °C

Full range and all datasheets: optical transceivers.

Coding, quality, warranty

Coded to your host, tested first.

Host vendor names describe the target platform only.

Coding & compatibility

WTQ1HZ8 is coded for the host platform you name, for example Cisco, Juniper, Huawei, Arista, Nokia switches and routers. We read and back up the module data, write the approved profile, then read back and verify it with DDM. Compatibility is validated per host model and software release, so we recommend testing coded samples on your equipment before a volume order.

Quality & warranty

Built in ISO 9001-certified manufacturing partners. CE, RoHS, FCC and TÜV test reports are available for each model on request.

Warranty: hardware 3 years, software 1 year.

FAQ

Questions on this model.

Not answered here? Email waley@wincoteknetwork.com or message us on WhatsApp.

Does WTQ1HZ8 need FEC?

Yes. The datasheet specifies up to 80 km with KR4 FEC, so enable KR4 FEC on both host ports.

Is an attenuator needed on shorter spans?

Usually. Average receive power must not exceed −6 dBm per lane and the transmitter launches up to 6.5 dBm per lane. Measure RX power in DDM and add an LC attenuator on short spans and loop-back tests.

What is the operating temperature and power?

0 to 70 °C case temperature and 6 W maximum power dissipation, from a single +3.3 V supply. Check that the host port supports a 6 W QSFP28 module.

How does ZR4 differ from ER4?

ER4 (WTQ1HE4) uses a PIN receiver, −18 dBm per lane, for up to 40 km. ZR4 (WTQ1HZ8) uses a PIN receiver with SOA, −27 dBm sensitivity per lane, for up to 80 km with KR4 FEC.

Can WTQ1HZ8 be coded for our host?

Yes. It is coded for the host platform you name and verified before shipping. Test coded samples on your equipment before a volume order.

Request a quote for WTQ1HZ8.

Send the host model and software release, quantity and coding needs. We reply with a matched P/N and sample plan.

Email waley@wincoteknetwork.com · WhatsApp / phone +86 176 8896 6828

WhatsApp