Home/Optical transceivers/100G QSFP28 BiDi 20 km

WincoTek 100G QSFP28 BiDi 20 km Transceiver(WTQ2Bxx020C0CN1)

WTQ2Bxx020C0CN1 is a 100G QSFP28 single-lambda BiDi transceiver for 100GBASE-LR1 links up to 20 km over one single-mode fiber. Each module sends one 106.25 Gb/s PAM4 lane from an EML laser and receives the opposite wavelength on a PIN receiver, through a simplex LC connector. It is ordered as a pair: WTQ2BL3020C0CN1 transmits 1271 nm, WTQ2BL2020C0CN1 transmits 1331 nm.

WincoTek 100G QSFP28 BiDi 20 km transceiver
Data rate
106.25 Gb/s PAM4
Reach
20 km SMF
Fiber
1 fiber, BiDi
Connector
Simplex LC
Key specifications

100G QSFP28 BiDi 20 km at a glance.

Main optical, electrical and environmental values for WTQ2Bxx020C0CN1.

ParameterValue
Ordering codesWTQ2BL3020C0CN1 (TX 1271 / RX 1331 nm, purple latch); WTQ2BL2020C0CN1 (TX 1331 / RX 1271 nm, red latch); both 0 to 70 °C
Data rate106.25 Gb/s PAM4 optical lane (111.8 Gb/s compatible); 4 × 25.78 Gb/s NRZ electrical interface (CAUI-4)
Application100GBASE-LR1-20 BiDi
WavelengthsTX 1271 nm (1264.5–1277.5 nm), RX 1331 nm (1324.5–1337.5 nm), reversed on the partner module
Laser / receiverEML laser, PIN receiver
TX power (avg.)−1.4 to 4.5 dBm; OMAouter 0.7 to 4.7 dBm; TDECQ 3.4 dB max.
RX sensitivity (OMAouter)−7.6 dBm for TECQ ≤ 1.4 dB; −9 + TECQ for 1.4 ≤ TECQ ≤ 3.6 dB
RX average receive power−10 to 6.6 dBm; damage threshold 7.6 dBm
ReachUp to 20 km on single-mode fiber
ConnectorSimplex LC
Form factorQSFP28 MSA; single +3.3 V supply (3.13 to 3.47 V); hardware TX_DIS and RX_LOS for telecom use
Power4.5 W max.; supply current 1.3 A max.
Case temperature0 to 70 °C
DDMYes, over I²C: temperature, voltage, TX bias, TX and RX power

Main values for WTQ2Bxx020C0CN1. Full WincoTek datasheet: DatasheetPDF

BiDi pairing

Used in pairs.

Each module transmits on one wavelength and receives on the other.

Order one of each.

A BiDi link sends and receives on one fiber, using two wavelengths. The two ends must be opposite halves of the same model, so order the modules as pairs in equal quantities.

WTQ2BL3020C0CN1End A: TX 1271 nm / RX 1331 nm
← one SMF →
WTQ2BL2020C0CN1End B: TX 1331 nm / RX 1271 nm

Both halves are rated 0 to 70 °C case temperature. Each end can be coded for a different host platform.

Typical applications

Where it is used.

From the datasheet application list and common network use.

  • 100G links between buildings or sites over one fiber, up to 20 km
  • Router and switch uplinks where duplex fiber pairs are used up
  • Metro access and aggregation rings
  • Running two 100G links on a fiber pair that today carries one
Selection notes

When single-fiber 100G pays off.

Fiber count, pairing and labeling.

A BiDi module sends and receives on one strand by using two wavelengths, so each 100G link needs one fiber instead of two. That halves patch-panel ports, trays and spliced fibers. The modules cost more than duplex ones, so BiDi pays off where fiber is the scarce resource.

The two ends carry different part numbers. Order WTQ2BL3020C0CN1 and WTQ2BL2020C0CN1 in equal quantities, keep the latch colors (purple and red) consistent across sites and label each end in the patch records.

Check the budget in both directions: launch power minus link loss and at least 3 dB of margin must land between the receiver sensitivity and the maximum receive power. For longer single-fiber spans see the 40 km and 70 km BiDi models; with a fiber pair free, the duplex 100G QSFP28 LR4 is the alternative.

How it compares

Related WincoTek models.

The 100G QSFP28 BiDi family, all on simplex LC. Order matching halves of one model for both ends.

ModelReachWavelengths (pair)ReceiverMax. power
WTQ2Bxx010C0CN1
DatasheetPDF
10 kmTX 1271 / RX 1331 nmPIN4 W
WTQ2Bxx020C0CN1
this page
DatasheetPDF
20 kmTX 1271 / RX 1331 nmPIN4.5 W
WTQ2Bxx030C0CN1
DatasheetPDF
30 kmTX 1304 / RX 1309 nmAPD4.5 W
WTB59(95)Y-40D
DatasheetPDF
40 kmTX 1305 / RX 1309 nmAPD<4 W
WT290
DatasheetPDF
70 kmLAN-WDM blue / red pairSOA5.5 W (0 to 70 °C) / 6 W (−20 to 85 °C)

Full range and all datasheets: optical transceivers.

Coding, quality, warranty

Coded to your host, tested first.

Host vendor names describe the target platform only.

Coding & compatibility

WTQ2Bxx020C0CN1 is coded for the host platform you name, for example Cisco, Juniper, Huawei, Arista, Nokia switches and routers. We read and back up the module data, write the approved profile, then read back and verify it with DDM. Compatibility is validated per host model and software release, so we recommend testing coded samples on your equipment before a volume order.

Quality & warranty

Built in ISO 9001-certified manufacturing partners. CE, RoHS, FCC and TÜV test reports are available for each model on request.

Warranty: hardware 3 years, software 1 year.

FAQ

Questions on this model.

Not answered here? Email waley@wincoteknetwork.com or message us on WhatsApp.

What does xx in WTQ2Bxx020C0CN1 stand for?

The wavelength side. WTQ2BL3020C0CN1 transmits 1271 nm and receives 1331 nm; WTQ2BL2020C0CN1 transmits 1331 nm and receives 1271 nm. One of each makes a link.

Which standard does it follow?

100GBASE-LR1-20 BiDi, with one 106.25 Gb/s PAM4 optical lane and a CAUI-4 (4 × 25.78 Gb/s) electrical interface to the host.

What are the optical levels?

Average launch power −1.4 to 4.5 dBm, receiver sensitivity (OMAouter) −7.6 dBm for TECQ up to 1.4 dB, and average receive power up to 6.6 dBm with a 7.6 dBm damage threshold.

Can I mix it with the 10 km or 40 km BiDi?

No. Use matching halves of the same model at both ends. The 10 km model shares the 1271/1331 nm pair but has different optical ranges; the 30 and 40 km models use a different wavelength pair.

Can WTQ2Bxx020C0CN1 be coded for our switches?

Yes. WTQ2Bxx020C0CN1 is coded for the host platform you name, then read back and verified. Compatibility is validated per host model and software release, so test coded samples before a volume order.

Request a quote for WTQ2Bxx020C0CN1.

Send the host model and software release, quantity and coding needs. We reply with a matched P/N and sample plan.

Email waley@wincoteknetwork.com · WhatsApp / phone +86 176 8896 6828

WhatsApp