Home/Optical transceivers/100G QSFP28 BiDi 40 km

WincoTek 100G QSFP28 BiDi 40 km Transceiver(WTB59(95)Y-40D)

WTB59(95)Y-40D is a 100G QSFP28 BiDi transceiver for 100GBASE-ER1 links up to 40 km over one single-mode fiber. It carries one 106.25 Gb/s PAM4 lane from an EML laser to an APD receiver, with KP4 FEC inside the module, on a simplex LC connector. Two halves make a link: WTB59Y-40D transmits 1305 nm and receives 1309 nm, WTB95Y-40D does the opposite.

WincoTek 100G QSFP28 BiDi 40 km transceiver
Data rate
106.25 Gb/s PAM4
Reach
40 km SMF
Receiver
APD
Power
<4 W
Key specifications

100G QSFP28 BiDi 40 km at a glance.

Main optical, electrical and environmental values for WTB59(95)Y-40D.

ParameterValue
Ordering codesWTB59Y-40D (TX 1305 / RX 1309 nm, green latch); WTB95Y-40D (TX 1309 / RX 1305 nm, blue latch); both 0 to 70 °C, with DDM
Data rate106.25 Gb/s PAM4 optical lane (53.125 GBd); 4 × 25.78 Gb/s NRZ electrical interface (CAUI-4)
Application100GBASE-ER1 BiDi; 100G Ethernet and data center links
Wavelengths1305 / 1309 nm pair (1304.58 and 1309.14 nm typ.)
Laser / receiverEML laser, APD receiver
FECKP4 FEC inside the module
TX power (avg.)1.7 to 7.1 dBm; TDECQ 3.9 dB max.; extinction ratio 5 dB min.
RX sensitivity (OMAouter)−13.8 dBm for TDECQ < 1.4 dB; −15.2 + TECQ for 1.4 ≤ TDECQ ≤ 3.4 dB
RX average receive power−16 to −3.4 dBm; damage threshold −2.4 dBm
ReachUp to 40 km on single-mode fiber
ConnectorSimplex LC
Power<4 W
Supply3.13 to 3.47 V
Case temperature0 to 70 °C
DDMYes: temperature, voltage, TX bias, TX power (1.7 to 7.1 dBm), RX power (−16 to −3.4 dBm)

Main values for WTB59(95)Y-40D. Full WincoTek datasheet: DatasheetPDF

Short links and testing. The transmitter launches up to 7.1 dBm, while average receive power must stay at or below −3.4 dBm (damage threshold −2.4 dBm). On short spans and in loop-back tests, read RX power in DDM and add an LC attenuator so the receiver sits between −16 and −3.4 dBm.
BiDi pairing

Used in pairs.

Each module transmits on one wavelength and receives on the other.

Order one of each.

A BiDi link sends and receives on one fiber, using two wavelengths. The two ends must be opposite halves of the same model, so order the modules as pairs in equal quantities.

WTB59Y-40DEnd A: TX 1305 nm / RX 1309 nm
← one SMF →
WTB95Y-40DEnd B: TX 1309 nm / RX 1305 nm

Both halves are rated 0 to 70 °C case temperature. Each end can be coded for a different host platform.

Typical applications

Where it is used.

From the datasheet application list and common network use.

  • 100G links up to 40 km on a single fiber
  • Metro aggregation and data center interconnect where fiber pairs are limited
  • Carrier backhaul between exchanges on leased or shared fiber
  • Adding 100G capacity on routes that cannot get new fiber
Selection notes

40 km on one strand.

FEC, receive power and the wavelength pair.

At 40 km the receiver works close to its limit, so this model uses an APD and runs KP4 FEC inside the module. The host connects over a CAUI-4 interface; send us the host model so we can confirm the port settings before samples ship.

The two wavelengths, 1305 and 1309 nm, sit about 4.5 nm apart in the 1310 nm band, where fiber dispersion is low. Keep both halves within this model: they do not pair with the 1271/1331 nm BiDi optics.

Too much light harms the receiver as much as too little starves it. Measure the span, add connector and splice losses plus at least 3 dB of margin, and attenuate short links. For 20 km see the 20 km BiDi; for longer single-fiber spans the 70 km BiDi; with a fiber pair free, the duplex 100G QSFP28 ER4.

How it compares

Related WincoTek models.

The 100G QSFP28 BiDi family, all on simplex LC. Order matching halves of one model for both ends.

ModelReachWavelengths (pair)ReceiverMax. power
WTQ2Bxx010C0CN1
DatasheetPDF
10 kmTX 1271 / RX 1331 nmPIN4 W
WTQ2Bxx020C0CN1
DatasheetPDF
20 kmTX 1271 / RX 1331 nmPIN4.5 W
WTQ2Bxx030C0CN1
DatasheetPDF
30 kmTX 1304 / RX 1309 nmAPD4.5 W
WTB59(95)Y-40D
this page
DatasheetPDF
40 kmTX 1305 / RX 1309 nmAPD<4 W
WT290
DatasheetPDF
70 kmLAN-WDM blue / red pairSOA5.5 W (0 to 70 °C) / 6 W (−20 to 85 °C)

Full range and all datasheets: optical transceivers.

Coding, quality, warranty

Coded to your host, tested first.

Host vendor names describe the target platform only.

Coding & compatibility

WTB59(95)Y-40D is coded for the host platform you name, for example Cisco, Juniper, Huawei, Arista, Nokia switches and routers. We read and back up the module data, write the approved profile, then read back and verify it with DDM. Compatibility is validated per host model and software release, so we recommend testing coded samples on your equipment before a volume order.

Quality & warranty

Built in ISO 9001-certified manufacturing partners. CE, RoHS, FCC and TÜV test reports are available for each model on request.

Warranty: hardware 3 years, software 1 year.

FAQ

Questions on this model.

Not answered here? Email waley@wincoteknetwork.com or message us on WhatsApp.

Which two part numbers make a link?

WTB59Y-40D (TX 1305 nm, RX 1309 nm, green latch) at one end and WTB95Y-40D (TX 1309 nm, RX 1305 nm, blue latch) at the other, on the same single-mode fiber.

Does it need an attenuator?

On short spans, yes. Launch power reaches 7.1 dBm while receive power must stay at or below −3.4 dBm, with a −2.4 dBm damage threshold. Check RX power in DDM after installation.

What receiver and FEC does it use?

An APD receiver, with receiver sensitivity (OMAouter) of −13.8 dBm for TDECQ below 1.4 dB, and KP4 FEC inside the module.

Which temperature range applies?

The datasheet rates both halves for 0 to 70 °C case temperature. For outdoor sites, ask us; the 70 km BiDi model has a −20 to 85 °C configuration.

Can WTB59(95)Y-40D be coded for our switches?

Yes. WTB59(95)Y-40D is coded for the host platform you name, then read back and verified. Compatibility is validated per host model and software release, so test coded samples before a volume order.

Request a quote for WTB59(95)Y-40D.

Send the host model and software release, quantity and coding needs. We reply with a matched P/N and sample plan.

Email waley@wincoteknetwork.com · WhatsApp / phone +86 176 8896 6828

WhatsApp