Home/Optical transceivers/100G QSFP28 BiDi 70 km

WincoTek 100G QSFP28 BiDi 70 km Transceiver(WT290)

WT290 is a 100G QSFP28 BiDi transceiver for links up to 70 km on G.652 single-mode fiber with RS(528,514) FEC. It transmits four 25 Gb/s lanes from cooled LAN-WDM EML lasers on one side of the LAN-WDM band and receives the other side, so a full 100G link runs on one fiber through a single LC receptacle. WT290-835 and WT290-836 form the blue / red pair, in a 0 to 70 °C or −20 to 85 °C configuration.

WincoTek 100G QSFP28 BiDi 70 km transceiver
Data rate
103.125 Gb/s
Reach
70 km SMF
Receiver
SOA
Power
5.5 W / 6 W
Key specifications

100G QSFP28 BiDi 70 km at a glance.

Main optical, electrical and environmental values for WT290.

ParameterValue
Ordering codesWT290-835 / WT290-836: the two halves of a blue / red LAN-WDM pair; application code 100GBASE-ZR4; DDM
Data rate103.125 Gb/s aggregate; 4 × 25.78125 Gb/s
OpticsCooled 4 × 25 Gb/s LAN-WDM EML transmitter on the blue or red side; receiver on the opposite side
ReceiverSOA
TX power+2 to +7 dBm
RX sensitivityBetter than −25 dBm at BER 5 × 10−5
RX damage threshold+5.5 dBm per lane
Reach / FECUp to 70 km on G.652 single-mode fiber with RS(528,514) FEC
ConnectorSingle LC receptacle
Power5.5 W max. for 0 to 70 °C; 6 W max. for −20 to 85 °C; 1.5 W in low power mode
Supply3.135 to 3.465 V; steady-state current 1732 mA max.
Case temperature0 to 70 °C configuration, or −20 to 85 °C with order-specific DDM thresholds
ManagementSFF-8636; IntL/RxLOSL and LPMode/TxDis configurable through the management interface
DDMYes: temperature ±3 °C, voltage ±3%, TX and RX power ±3 dB; warning thresholds TX 2 to 7 dBm, RX −25 to −6.5 dBm
EnvironmentalRoHS 2.0

Main values for WT290. Full WincoTek datasheet: DatasheetPDF

Short links and testing. The datasheet sets the RX power high warning at −6.5 dBm and the high alarm at −3.5 dBm, while the transmitter launches up to +7 dBm. On spans much shorter than 70 km and in loop-back tests, read RX power in DDM and attenuate so the receiver stays below the warning level.
BiDi pairing

Used in pairs.

Each module transmits on one wavelength and receives on the other.

Order one of each.

A BiDi link sends and receives on one fiber, using two wavelengths. The two ends must be opposite halves of the same model, so order the modules as pairs in equal quantities.

WT290-835End A: One side of the blue / red LAN-WDM pair
← one SMF →
WT290-836End B: The complementary side

Confirm the wavelength pair for both ends with the order; the −20 to 85 °C configuration also gets order-specific alarm thresholds. Each end can be coded for a different host platform.

Typical applications

Where it is used.

From the datasheet application list and common network use.

  • 100G links up to 70 km on a single fiber
  • Regional backhaul and long metro spans where only one strand is available
  • Data center interconnect over leased single fibers
  • Outdoor and unconditioned sites with the −20 to 85 °C configuration
Selection notes

70 km, one strand, no DWDM line.

Loss, FEC and the pair.

At 70 km the fiber takes most of the budget. The reach is rated on G.652 fiber with RS(528,514) FEC, so enable FEC on both host ports. Measure the span: fiber, connectors and splices plus at least 3 dB of margin must fit between the +2 dBm minimum launch power and the −25 dBm sensitivity.

Each module transmits four LAN-WDM lanes on one side of the band and receives the other side. Order WT290-835 and WT290-836 together, in the same temperature configuration, and confirm the pair for both ends with the order.

Where a fiber pair is available, the duplex 100G QSFP28 ZR4 covers up to 80 km; for shorter single-fiber spans see the 40 km BiDi. For many 100G links on one route, a DWDM system scales further: DWDM vs CWDM for metro networks.

How it compares

Related WincoTek models.

The 100G QSFP28 BiDi family, all on simplex LC. Order matching halves of one model for both ends.

ModelReachWavelengths (pair)ReceiverMax. power
WTQ2Bxx010C0CN1
DatasheetPDF
10 kmTX 1271 / RX 1331 nmPIN4 W
WTQ2Bxx020C0CN1
DatasheetPDF
20 kmTX 1271 / RX 1331 nmPIN4.5 W
WTQ2Bxx030C0CN1
DatasheetPDF
30 kmTX 1304 / RX 1309 nmAPD4.5 W
WTB59(95)Y-40D
DatasheetPDF
40 kmTX 1305 / RX 1309 nmAPD<4 W
WT290
this page
DatasheetPDF
70 kmLAN-WDM blue / red pairSOA5.5 W (0 to 70 °C) / 6 W (−20 to 85 °C)

Full range and all datasheets: optical transceivers.

Coding, quality, warranty

Coded to your host, tested first.

Host vendor names describe the target platform only.

Coding & compatibility

WT290 is coded for the host platform you name, for example Cisco, Juniper, Huawei, Arista, Nokia switches and routers. We read and back up the module data, write the approved profile, then read back and verify it with DDM. Compatibility is validated per host model and software release, so we recommend testing coded samples on your equipment before a volume order.

Quality & warranty

Built in ISO 9001-certified manufacturing partners. CE, RoHS, FCC and TÜV test reports are available for each model on request.

Warranty: hardware 3 years, software 1 year.

FAQ

Questions on this model.

Not answered here? Email waley@wincoteknetwork.com or message us on WhatsApp.

Is WT290 rated for 70 km or 80 km?

70 km. The datasheet gives up to 70 km on G.652 single-mode fiber with RS(528,514) FEC. For 80 km on a fiber pair, use the 100G QSFP28 ZR4.

How is the pair made up?

WT290-835 and WT290-836 are the two halves of a blue / red LAN-WDM pair: each transmits on one side of the band and receives the other. Use one of each on the same fiber.

What are the optical levels?

Transmit power +2 to +7 dBm and receiver sensitivity better than −25 dBm at a bit error ratio of 5 × 10⁻⁵, with a +5.5 dBm damage threshold per lane.

Which temperature ranges and power apply?

Up to 5.5 W in the 0 to 70 °C configuration and 6 W in the −20 to 85 °C configuration. Extended-range units get order-specific alarm thresholds.

Can WT290 be coded for our switches?

Yes. WT290 is coded for the host platform you name, then read back and verified. Compatibility is validated per host model and software release, so test coded samples before a volume order.

Request a quote for WT290.

Send the host model and software release, quantity and coding needs. We reply with a matched P/N and sample plan.

Email waley@wincoteknetwork.com · WhatsApp / phone +86 176 8896 6828

WhatsApp