Home/Optical transceivers/100G QSFP28 PAM4 DWDM

WincoTek 100G QSFP28 PAM4 DWDM 80 km Transceiver(WTQ2Dxx080C0CN1)

WTQ2Dxx080C0CN1 is a 100G QSFP28 DWDM transceiver for data center interconnect and metro links up to 80 km on G.652 fiber with a DWDM line system. It splits 100G into two PAM4 carriers at 27.5 GBd, each on its own 100 GHz ITU channel, using a cooled EML transmitter and PIN receivers with integrated FEC. The xx in the part number is the channel code, from 13 to 60.

WincoTek 100G QSFP28 PAM4 DWDM transceiver
Data rate
103.1 Gb/s
Reach
80 km with line system
Grid
C-band, 100 GHz
Connector
Dual CS
Key specifications

100G QSFP28 PAM4 DWDM at a glance.

Main optical, electrical and environmental values for WTQ2Dxx080C0CN1.

ParameterValue
Ordering codesWTQ2D13080C0CN1 to WTQ2D60080C0CN1; xx = channel code, each code uses two channels (for example 13: C13 + C14, 191.30 / 191.40 THz)
Data rate103.1 Gb/s; 4 × 25G CAUI-4 electrical; 2 optical carriers of 55.04 Gb/s PAM4 (27.5 GBd)
WavelengthsC-band, 100 GHz ITU grid; channels C13 to C60 and C13+ to C60+ (191.30 to 196.05 THz)
Laser / receiverCooled EML DWDM transmitter; PIN photodiode receiver
FECIntegrated FEC (SFEC) in the module
TX optical output power−1 to +7 dBm; extinction ratio 6 dB min.
RX sensitivity−7.2 dBm at pre-FEC BER 2 × 10−4; required OSNR 31 dB
Dispersion tolerance−100 to +100 ps/nm residual dispersion (after dispersion compensation)
RX damage threshold+5.2 dBm per lane
ReachUp to 80 km on G.652 single-mode fiber with a DWDM transport line system
ConnectorDual CS
Power5 W max. (70 °C, 3.465 V, end of life)
Case temperature0 to 70 °C
EnvironmentalRoHS 6 compatible

Main values for WTQ2Dxx080C0CN1. Full WincoTek datasheet: DatasheetPDF

Typical applications

Where it is used.

From the datasheet application list and common network use.

  • 100G data center interconnect over DWDM
  • 100G Ethernet metro access over a DWDM line
  • Point-to-point access links sharing one fiber pair by wavelength
Selection notes

Ordered by channel, built into a line.

How a PAM4 DWDM optic fits a metro link.

A DWDM optic is ordered by channel, not only by reach. Each WTQ2Dxx080C0CN1 code uses two neighbouring channels (TX1 and TX2), so map every module to its multiplexer ports before ordering.

PAM4 at 1550 nm is sensitive to dispersion and noise. The datasheet tolerance is ±100 ps/nm of residual dispersion and the required OSNR is 31 dB, so an 80 km span needs a line system with dispersion compensation and amplification. A QSFP28 EDFA can supply the gain from a QSFP28 port.

The module front is a dual CS connector, smaller than duplex LC. Plan patch cords with CS ends at the module side. For multiplexers and line equipment see DWDM / OTN.

How it compares

Related WincoTek models.

100G options for metro and DCI. PAM4 DWDM needs a line system; coherent DCO modules handle dispersion in the module.

ModelTypeOpticsReachNotes
WTQ2Dxx080C0CN1
this page
DatasheetPDF
100G QSFP28 PAM4 DWDM2 C-band channels, 100 GHz grid80 km with DWDM line systemDual CS; 5 W max.
WTQ1HZ8
DatasheetPDF
100G QSFP28 ZR4LAN-WDM EML / SOA80 kmDuplex LC; KR4 FEC
WTQDS100SZPTA00
DatasheetPDF
100G QSFP-DD OpenZR+ DCOCoherent DP-QPSK, tunable C-bandSet by OSNR and line system16.5 W max.
WTCTS100SMRTA00
DatasheetPDF
100G CFP2 DCOCoherent DP-QPSK, tunable C-bandSet by OSNR and line system21 W max. at 100G
WTQ28-EDFA
DatasheetPDF
QSFP28 EDFAAmplifier, 1528–1561 nmLine amplifierPre-amp or booster, 22 dB gain

Full range and all datasheets: optical transceivers. Guide: DWDM vs CWDM for metro networks.

Coding, quality, warranty

Coded to your host, tested first.

Host vendor names describe the target platform only.

Coding & compatibility

WTQ2Dxx080C0CN1 is coded for the host platform you name, for example Cisco, Juniper, Huawei, Arista, Nokia switches and routers. We read and back up the module data, write the approved profile, then read back and verify it with DDM. Compatibility is validated per host model and software release, so we recommend testing coded samples on your equipment before a volume order.

Quality & warranty

Built in ISO 9001-certified manufacturing partners. CE, RoHS, FCC and TÜV test reports are available for each model on request.

Warranty: hardware 3 years, software 1 year.

FAQ

Questions on this model.

Not answered here? Email waley@wincoteknetwork.com or message us on WhatsApp.

What does xx in WTQ2Dxx080C0CN1 mean?

It is the channel code, from 13 to 60. Each code uses two channels 100 GHz apart: code 13 uses C13 (191.30 THz) and C14 (191.40 THz), code 14 uses C13+ and C14+, 50 GHz higher, and so on up to code 60.

Can it run 80 km without amplifiers?

The datasheet rates 80 km on G.652 fiber with a DWDM transport line system. With ±100 ps/nm residual dispersion tolerance and a required OSNR of 31 dB, plan dispersion compensation and amplification on the span.

Does the host need FEC?

The module integrates its own FEC (SFEC); its receiver sensitivity of −7.2 dBm is specified at a pre-FEC bit error ratio of 2 × 10⁻⁴.

Which connector does it use?

A dual CS connector. Use patch cords with CS connectors on the module side.

Can WTQ2Dxx080C0CN1 be coded for our switches?

Yes. WTQ2Dxx080C0CN1 is coded for the host platform you name, then read back and verified. Compatibility is validated per host model and software release, so test coded samples before a volume order.

Request a quote for WTQ2Dxx080C0CN1.

Send the host model and software release, quantity and coding needs. We reply with a matched P/N and sample plan.

Email waley@wincoteknetwork.com · WhatsApp / phone +86 176 8896 6828

WhatsApp