WincoTek 100G CFP2-DCO Coherent Module(WTCTS100SMRTA00)

WTCTS100SMRTA00 is a 100G coherent CFP2 digital optics (DCO) module for metro and long-haul DWDM. It transmits DP-QPSK at 31.57 GBd with oFEC on one channel tunable across the C-band 50 GHz grid, and carries a 100GbE (CAUI-4) or OTU4 (OTL4.4) client. A 200G DP-16QAM version, WTCTS200SMRTA00, shares the same design.

At a glance

Product photo on request. The full datasheet is linked below.

Line rate
100G DP-QPSK
FEC
oFEC
Tuning
191.3–196.1 THz, 50 GHz
Client
100GbE or OTU4
Key specifications

100G CFP2-DCO at a glance.

Main optical, electrical and environmental values for WTCTS100SMRTA00.

ParameterValue
Ordering codesWTCTS100SMRTA00: 100 Gb/s single channel tunable coherent CFP2, DP-QPSK, oFEC, 0 to 70 °C. WTCTS200SMRTA00: 200 Gb/s, DP-16QAM, oFEC
Client interface1 × CAUI-4 (100GbE, 4 × 25 Gb/s) or 1 × OTL4.4 (OTU4, 4 × 28 Gb/s); 200G version 2 × CAUI-4 or 2 × OTL4.4
Line side100G DP-QPSK, 31.57 GBd, oFEC, 50 GHz grid
Frequency range191.3 to 196.10 THz (C-band, 50 GHz ITU-T grid); fine tuning ±6 GHz in 100 MHz steps
LaserFrequency stability ±2.5 GHz; linewidth 500 kHz; channel tuning 80 s max.
TX output power−5 to +5 dBm, settable in 0.1 dB steps; TX OSNR 35 dB/0.1 nm
RX input power range−18 to 0 dBm
RX sensitivity−21 dBm (post-FEC BER < 10−15, OSNR > 35 dB)
OSNR sensitivity100G DP-QPSK: 11.5 dB/0.1 nm typ., 12.5 max.; 200G DP-16QAM: 19.5 typ., 21 max.
TolerancesChromatic dispersion 40000 ps/nm; DGD 50 ps; PDL 3 dB; SOP change 50 rad/ms
Power18 W typ., 21 W max. (100G DP-QPSK); 22 W typ., 24 W max. (200G); 2 W in low power mode
Supply3.2 to 3.4 V
Case temperature0 to 70 °C
ManagementMDIO

Main values for WTCTS100SMRTA00. Full WincoTek datasheet: DatasheetPDF

Typical applications

Where it is used.

From the datasheet application list and common network use.

  • 100G metro and regional DWDM transport
  • OTU4 and 100GbE clients onto a coherent wavelength
  • Data center interconnect over long or amplified spans
  • Routers and transport platforms with CFP2 line ports
Selection notes

When coherent pays off.

Coherent 100G against PAM4 DWDM on a metro span.

A coherent receiver corrects chromatic dispersion in its DSP. This module tolerates 40000 ps/nm, so spans need no dispersion compensation modules, which PAM4 DWDM optics rely on.

Coherent links are limited mainly by OSNR. At 100G DP-QPSK the module needs 12.5 dB/0.1 nm at most, which leaves room for long, amplified spans. Plan amplifiers and channel loading with the line system.

The client side carries 100GbE or OTU4. If the host needs more capacity per wavelength, the 200G DP-16QAM version needs about 19.5 dB/0.1 nm OSNR instead. For line systems see DWDM / OTN.

How it compares

Related WincoTek models.

Coherent DCO options in CFP2 and QSFP-DD. Use the same type and FEC at both ends of a wavelength.

ModelForm factorLine rateModulation / FECMax. power
WTQDS400SZPTA00
DatasheetPDF
QSFP-DD400G OpenZR+DP-16QAM / oFEC21 W
WTQDS400SZRTA00
DatasheetPDF
QSFP-DD400G ZRDP-16QAM / CFEC18.5 W
WTQDS100SZPTA00
DatasheetPDF
QSFP-DD100G OpenZR+DP-QPSK / oFEC16.5 W
WTCTS100SMRTA00
this page
DatasheetPDF
CFP2100G (200G version: WTCTS200SMRTA00)DP-QPSK (100G) or DP-16QAM (200G) / oFEC21 W (100G), 24 W (200G)
WTCTS400SLHTA00
DatasheetPDF
CFP2400G / 200GPS-16QAM at 400G25 W at 400G

Full range and all datasheets: optical transceivers.

Coding, quality, warranty

Coded to your host, tested first.

Coding on request, validated per host model and software release.

Host support

WTCTS100SMRTA00 plugs into a CFP2 port and is managed over MDIO under the CFP2 MSA. Coherent line cards differ in the CFP2-DCO profiles they accept, so send us the host model and software release. We confirm the configuration and recommend testing samples on your equipment before a volume order.

Quality & warranty

Built in ISO 9001-certified manufacturing partners. CE, RoHS, FCC and TÜV test reports are available for each model on request.

Warranty: hardware 3 years, software 1 year.

FAQ

Questions on this model.

Not answered here? Email waley@wincoteknetwork.com or message us on WhatsApp.

Which clients does WTCTS100SMRTA00 carry?

One 100GbE client over CAUI-4 (4 × 25 Gb/s) or one OTU4 client over OTL4.4 (4 × 28 Gb/s).

What is the difference from WTCTS200SMRTA00?

The 200G version uses DP-16QAM and carries two 100G clients, at up to 24 W and 21 dB/0.1 nm OSNR sensitivity. WTCTS100SMRTA00 uses DP-QPSK at up to 21 W and 12.5 dB/0.1 nm.

Does the span need dispersion compensation?

No DCM is needed for dispersion within the module tolerance: the datasheet gives 40000 ps/nm chromatic dispersion tolerance.

Which channels can it use?

It tunes across 191.3 to 196.10 THz on the 50 GHz C-band grid, with ±6 GHz fine tuning in 100 MHz steps.

Will it work in our router?

It is a CFP2 module managed over MDIO. Send us the host model and software release, and test samples on your equipment before a volume order.

Request a quote for WTCTS100SMRTA00.

Send the host model and software release, quantity and coding needs. We reply with a matched P/N and sample plan.

Email waley@wincoteknetwork.com · WhatsApp / phone +86 176 8896 6828

WhatsApp