Home/Optical transceivers/400G QSFP-DD OpenZR+ DCO

WincoTek 400G QSFP-DD OpenZR+ Coherent DCO(WTQDS400SZPTA00)

WTQDS400SZPTA00 is a 400G coherent digital optics (DCO) module in QSFP-DD for OpenZR+ links. It carries 400G as DP-16QAM at 60.14 GBd with oFEC, on a single channel tunable across the C-band from 191.3 to 196.1 THz. Plugged straight into a router or switch port, it puts 400G onto a DWDM line system without a separate transponder.

WincoTek 400G QSFP-DD OpenZR+ DCO coherent module
Line rate
400G (481.1 Gb/s)
Modulation
DP-16QAM, oFEC
Tuning
C-band 191.3–196.1 THz
Form factor
QSFP-DD
Key specifications

400G QSFP-DD OpenZR+ DCO at a glance.

Main optical, electrical and environmental values for WTQDS400SZPTA00.

ParameterValue
Ordering codeWTQDS400SZPTA00: single rate 400 Gb/s, single channel tunable coherent QSFP-DD OpenZR+ with oFEC, 0 to 70 °C
Host interface1 × 400GAUI-8 (8 × 26.5625 GBd PAM4) or 4 × 100GAUI-2
Line side481.108 Gb/s, 60.1385 GBd, DP-16QAM, oFEC
Frequency range191.3 to 196.1 THz (C-band, 75 GHz ITU-T grid); fine tuning ±6 GHz in 100 MHz steps
LaserFrequency stability and accuracy ±1.8 GHz; linewidth 100 kHz; channel tuning 60 s max.
TX output power−10 to −6 dBm; TX OSNR (in-band) 34 dB/0.1 nm min.
RX input power range−12 to 0 dBm
RX sensitivity−20 dBm (post-FEC BER < 10−15 with OSNR > 26 dB/0.1 nm)
OSNR sensitivity22 dB/0.1 nm typ., 24 dB/0.1 nm max.
TolerancesChromatic dispersion 9000 ps/nm; PMD 20 ps; peak PDL 3.5 dB; SOP change 50 rad/ms
Power21 W
Supply3.135 to 3.465 V
Case temperature0 to 70 °C
EMCEMI FCC Class B; ESD IEC 61000-4-2

Main values for WTQDS400SZPTA00. Full WincoTek datasheet: DatasheetPDF

Typical applications

Where it is used.

From the datasheet application list and common network use.

  • IP over DWDM: 400G router and switch ports straight onto a DWDM line
  • Metro and regional data center interconnect
  • Aggregation of 4 × 100G clients onto one 400G wavelength
  • Capacity upgrades on existing C-band DWDM systems
Selection notes

Coherent in a pluggable.

What decides whether an OpenZR+ link closes.

A coherent link is limited by optical signal-to-noise ratio as much as by power. Plan the line system (multiplexers, amplifiers, span losses) so the received OSNR stays above the module's OSNR sensitivity with margin, and keep the received power within −12 to 0 dBm.

OpenZR+ uses oFEC. A 400ZR link with CFEC needs the ZR version, WTQDS400SZRTA00, at both ends. Order the same type for both ends of a wavelength.

Each module is tuned to one channel at a time. Agree the channel plan with your DWDM line before ordering, and check that the host port supports a coherent QSFP-DD module. For line systems see DWDM / OTN.

How it compares

Related WincoTek models.

Coherent DCO options in QSFP-DD and CFP2. Use the same type and FEC at both ends of a wavelength.

ModelForm factorLine rateModulation / FECMax. power
WTQDS400SZPTA00
this page
DatasheetPDF
QSFP-DD400G OpenZR+DP-16QAM / oFEC21 W
WTQDS400SZRTA00
DatasheetPDF
QSFP-DD400G ZRDP-16QAM / CFEC18.5 W
WTQDS100SZPTA00
DatasheetPDF
QSFP-DD100G OpenZR+DP-QPSK / oFEC16.5 W
WTCTS100SMRTA00
DatasheetPDF
CFP2100G (200G version: WTCTS200SMRTA00)DP-QPSK (100G) or DP-16QAM (200G) / oFEC21 W (100G), 24 W (200G)
WTCTS400SLHTA00
DatasheetPDF
CFP2400G / 200GPS-16QAM at 400G25 W at 400G

Full range and all datasheets: optical transceivers.

Coding, quality, warranty

Coded to your host, tested first.

Host vendor names describe the target platform only.

Coding & compatibility

WTQDS400SZPTA00 is coded for the host platform you name, for example Cisco, Juniper, Huawei, Arista, Nokia switches and routers. We read and back up the module data, write the approved profile, then read back and verify it with DDM. Compatibility is validated per host model and software release, so we recommend testing coded samples on your equipment before a volume order.

Quality & warranty

Built in ISO 9001-certified manufacturing partners. CE, RoHS, FCC and TÜV test reports are available for each model on request.

Warranty: hardware 3 years, software 1 year.

FAQ

Questions on this model.

Not answered here? Email waley@wincoteknetwork.com or message us on WhatsApp.

Is WTQDS400SZPTA00 the same as a 400ZR module?

No. It is an OpenZR+ module with oFEC. For 400ZR with CFEC, WincoTek offers WTQDS400SZRTA00. Use the same type at both ends.

Which host interfaces are supported?

One 400GAUI-8 interface, or four 100GAUI-2 interfaces, per the datasheet application table.

How far does it reach?

Reach depends on the line system: OSNR, amplifiers and fiber. The datasheet gives an OSNR sensitivity of 24 dB/0.1 nm maximum, a chromatic dispersion tolerance of 9000 ps/nm and a received power range of −12 to 0 dBm. Send us your span plan and we check it.

Which channels can it use?

It tunes across 191.3 to 196.1 THz in the C-band, with ±6 GHz fine tuning in 100 MHz steps.

Can WTQDS400SZPTA00 be coded for our switches?

Yes. WTQDS400SZPTA00 is coded for the host platform you name, then read back and verified. Compatibility is validated per host model and software release, so test coded samples before a volume order.

Request a quote for WTQDS400SZPTA00.

Send the host model and software release, quantity and coding needs. We reply with a matched P/N and sample plan.

Email waley@wincoteknetwork.com · WhatsApp / phone +86 176 8896 6828

WhatsApp