WincoTek QSFP28 EDFA Pluggable Optical Amplifier(WTQ28-EDFA)

WTQ28-EDFA is an erbium-doped fiber amplifier in a QSFP28 pluggable. It gives a fixed 22 dB gain under automatic gain control across 1528 to 1561 nm, for one to 40 DWDM channels, and is managed over I2C like an optic. It comes as a pre-amplifier (WTQ28-EDFA-PA2208) or a booster (WTQ28-EDFA-BA2213), so amplification can live in a switch or line card port.

At a glance

Product photo on request. The full datasheet is linked below.

Gain
22 dB, AGC
Band
1528–1561 nm
Channels
1 to 40
Power
3 W
Key specifications

QSFP28 EDFA at a glance.

Main optical, electrical and environmental values for WTQ28-EDFA.

ParameterValue
VersionsWTQ28-EDFA-PA2208 (pre-amplifier); WTQ28-EDFA-BA2213 (booster)
Wavelength range1528 to 1561 nm, input and output
Working channels1 to 40
Operation modeAGC (automatic gain control), fixed gain 22 dB
Input power−30 to −14 dBm (PA2208); −22 to −9 dBm (BA2213)
Output signal power−8 to 8 dBm (PA2208); 0 to 13 dBm (BA2213)
Noise figure6 dB typ., 7 dB max.
Gain flatness1.5 dB max. (room temperature, gain 22 dB)
PolarizationPDG 0.5 dB; PMD 0.5 ps
MonitoringInput and output power monitors, accuracy ±0.5 dB; LOS; EDFA bias; temperature and voltage
ManagementI²C, SFF-8636-based memory map (identifier 0x82, QSFP EDFA)
Supply / power3.14 to 3.47 V; total supply current 900 mA; power dissipation 3 W
Case temperature−5 to 70 °C; storage −40 to 85 °C
ComplianceClass 1M laser safety; RoHS 2.0 (2015/863)

Main values for WTQ28-EDFA. Full WincoTek datasheet: DatasheetPDF

Typical applications

Where it is used.

From the datasheet application list and common network use.

  • Booster at the transmit end of a short DWDM span
  • Pre-amplifier ahead of the receivers at the far end
  • Amplification for 100G PAM4 DWDM data center interconnect
  • Adding gain to a line without a separate amplifier shelf
Selection notes

Booster or pre-amplifier?

Choose the version by where it sits in the span.

A booster sits after the multiplexer at the transmit end and raises the combined signal before the fiber. The BA2213 version takes −22 to −9 dBm in and delivers 0 to 13 dBm out.

A pre-amplifier sits before the demultiplexer at the receive end and lifts a weak signal for the receivers. The PA2208 version accepts −30 to −14 dBm and delivers −8 to 8 dBm.

Both run fixed 22 dB gain with AGC across 1528 to 1561 nm for up to 40 channels. Pair it with 100G QSFP28 PAM4 DWDM optics, and check that the host port supports a 3 W QSFP28 amplifier module.

How it compares

Related WincoTek models.

The two WTQ28-EDFA versions. Choose by position in the span and the power you expect at the input.

VersionRoleInput powerOutput signal powerGain
WTQ28-EDFA-PA2208
DatasheetPDF
Pre-amplifier−30 to −14 dBm−8 to 8 dBm22 dB, fixed (AGC)
WTQ28-EDFA-BA2213
DatasheetPDF
Booster−22 to −9 dBm0 to 13 dBm22 dB, fixed (AGC)

Full range and all datasheets: optical transceivers. Guide: DWDM vs CWDM for metro networks.

Coding, quality, warranty

Coded to your host, tested first.

Coding on request, validated per host model and software release.

Host support

WTQ28-EDFA plugs into a QSFP28 port and is managed over I²C, using an SFF-8636-based memory map with identifier 0x82 (QSFP EDFA). It reports input and output power, EDFA bias, temperature and voltage, with alarm and warning thresholds. Check with us that your host platform and software release accept a QSFP28 amplifier, and test samples on your equipment before a volume order.

Quality & warranty

Built in ISO 9001-certified manufacturing partners. CE, RoHS, FCC and TÜV test reports are available for each model on request.

Warranty: hardware 3 years, software 1 year.

FAQ

Questions on this model.

Not answered here? Email waley@wincoteknetwork.com or message us on WhatsApp.

What is the difference between PA2208 and BA2213?

PA2208 is the pre-amplifier: −30 to −14 dBm input, −8 to 8 dBm output. BA2213 is the booster: −22 to −9 dBm input, 0 to 13 dBm output. Both have 22 dB fixed gain.

How many channels can it amplify?

One to 40 channels within 1528 to 1561 nm, under automatic gain control.

What is the noise figure?

6 dB typical and 7 dB maximum, with 1.5 dB maximum gain flatness at 22 dB gain.

How much power does it draw?

3 W power dissipation, up to 900 mA total supply current at 3.3 V. Case temperature −5 to 70 °C.

Will our switch recognise it?

It uses an SFF-8636-based memory map with a QSFP EDFA identifier. Send us the host model and software release, and test samples before a volume order.

Request a quote for WTQ28-EDFA.

Send the host model and software release, quantity and coding needs. We reply with a matched P/N and sample plan.

Email waley@wincoteknetwork.com · WhatsApp / phone +86 176 8896 6828

WhatsApp