Home/Optical transceivers/XGS-PON OLT N1 SFP+

WincoTek XGS-PON OLT N1 SFP+ Transceiver(WTXGSPON-OLT-N1-20)

WTXGSPON-OLT-N1-20 is an SFP+ OLT transceiver for XGS-PON networks to ITU-T G.9807.1, class N1, up to 20 km. It transmits 9.953 Gb/s downstream from a continuous-mode 1577 nm EML laser and receives upstream bursts at 1270 nm on an APD-TIA receiver, at 9.953 or 2.488 Gb/s. One SC/UPC fiber carries both directions to the passive optical distribution network.

At a glance

Product photo on request. The full datasheet is linked below.

Downstream
9.953 Gb/s, 1577 nm
Upstream
9.953 / 2.488 Gb/s, 1270 nm
Reach
20 km, class N1
Connector
SC/UPC
Key specifications

XGS-PON OLT N1 SFP+ at a glance.

Main optical, electrical and environmental values for WTXGSPON-OLT-N1-20.

ParameterValue
Ordering codesWTXGSPON-OLT-N1-20C (0 to 70 °C); WTXGSPON-OLT-N1-20I (−40 to 85 °C)
StandardITU-T G.9807.1 XGS-PON OLT, class N1
Data rateTX 9.95328 Gb/s continuous; RX 9.95328 or 2.48832 Gb/s burst, set by the rate-select pin (high = 10G, low = 2.5G)
Transmitter1577 nm EML (1575–1580 nm); average launch power 2 to 5 dBm; extinction ratio 8.2 dB min.
Receiver1270 nm (1260–1280 nm) burst-mode APD-TIA, with reset and RSSI trigger inputs
RX sensitivity−26 dBm at 9.953 Gb/s; −27.5 dBm at 2.488 Gb/s
RX saturation−5 dBm at 9.953 Gb/s; −7 dBm at 2.488 Gb/s
RX optical isolation−32 dB for external light below 1260 nm and above 1280 nm
ReachUp to 20 km on single-mode fiber
ConnectorSC/UPC receptacle, single fiber
Form factorSFP+, 20-pin; +3.3 V supply (3.13 to 3.47 V)
Power2.5 W max.; supply current 796 mA max.
Case temperature0 to 70 °C (C) or −40 to 85 °C (I)
DDMYes, two-wire interface: temperature, voltage, bias, TX power (2 to 5 dBm), RX power (−27.5 to −7 dBm)
EnvironmentalRoHS with exemptions, per datasheet

Main values for WTXGSPON-OLT-N1-20. Full WincoTek datasheet: DatasheetPDF

Short links and testing. The burst receiver saturates at −5 dBm (10G) or −7 dBm (2.5G). On a short or lightly split ODN, and in lab tests with an ONU next to the OLT, check the received upstream power and add attenuation so it stays below saturation.
Typical applications

Where it is used.

From the datasheet application list and common network use.

  • XGS-PON FTTH and FTTB access from the OLT line card
  • Symmetric 10G business and enterprise access over a PON
  • Upstream from 10G ONUs and 2.5G-upstream ONUs, selected by the rate-select pin
  • Outdoor OLT cabinets with the industrial grade
Selection notes

Plan the ODN first.

Loss budget, coexistence with GPON and temperature grade.

An OLT optic serves every ONU behind its splitter tree, so the ODN decides the choice. Add fiber, splitter, connector and splice losses, then keep at least 3 dB of margin. A 1×32 P-grade splitter alone takes up to 16.5 dB and a 1×64 up to 20.2 dB, per the FTTx splitter table. Compare the total with the launch power and receiver values above and with the ONU optics you plan to use.

XGS-PON runs at 1577 nm down and 1270 nm up, apart from GPON at 1490 / 1310 nm, so both systems can share one ODN with wavelength combining at the OLT side. WincoTek also offers WTXGSP01, which carries XGS-PON and GPON in one SFP+.

Choose the C grade for conditioned central offices and the I grade (−40 to 85 °C) for outdoor cabinets. For splitters, drop cable and pre-terminated cabling see FTTx passives; our ODN guide works through a loss budget.

How it compares

Related WincoTek models.

WincoTek PON optics for the OLT and the subscriber end. Size the class from the ODN loss budget.

ModelRoleRate (down / up)WavelengthsReach / class
WTXGSPON-OLT-N1-20
this page
DatasheetPDF
XGS-PON OLT, SFP+9.953 / 9.953 or 2.488 Gb/sTX 1577 / RX 1270 nm20 km, N1
WTXGSP01
DatasheetPDF
XGS-PON / GPON combo OLT, SFP+XGS-PON and GPON rates1270–1577 nm20 km, N1 + B+ or N2 + C+
WTG02TC3
DatasheetPDF
GPON OLT, SFP2.488 / 1.244 Gb/sTX 1490 / RX 1310 nm20 km, C+++
WTXPON-ONU-STICK
DatasheetPDF
GPON / EPON ONU stick, SFPGPON 2.488 / 1.244 Gb/s; EPON 1.25 / 1.25 Gb/sTX 1310 / RX 1490 nm20 km

Full range and all datasheets: optical transceivers. Guide: Pre-terminated ODN for FTTH deployments.

Coding, quality, warranty

Coded to your host, tested first.

Coding on request, validated per host model and software release.

Coding & compatibility

WTXGSPON-OLT-N1-20 is coded for the OLT platform and line card you name. We read and back up the module data, write the approved profile, then read back and verify it with DDM. Compatibility is validated per OLT model, line card and software release, so we recommend testing samples on your equipment, with the ONUs you plan to use, before a volume order.

Quality & warranty

Built in ISO 9001-certified manufacturing partners. CE, RoHS, FCC and TÜV test reports are available for each model on request.

Warranty: hardware 3 years, software 1 year.

FAQ

Questions on this model.

Not answered here? Email waley@wincoteknetwork.com or message us on WhatsApp.

Which PON standard does WTXGSPON-OLT-N1-20 support?

ITU-T G.9807.1 XGS-PON, OLT side, class N1, up to 20 km.

Which wavelengths and rates does it use?

1577 nm continuous downstream at 9.953 Gb/s and 1270 nm burst upstream at 9.953 or 2.488 Gb/s, selected by the rate-select pin.

What are the receiver values?

Sensitivity −26 dBm at 9.953 Gb/s and −27.5 dBm at 2.488 Gb/s, with saturation at −5 dBm and −7 dBm, per the datasheet.

Can it share an ODN with GPON?

Yes, with wavelength combining at the OLT side: XGS-PON uses 1577 / 1270 nm and GPON 1490 / 1310 nm. WincoTek also offers WTXGSP01, a combo XGS-PON and GPON OLT optic in one SFP+.

Can WTXGSPON-OLT-N1-20 be coded for our OLT?

Yes. WTXGSPON-OLT-N1-20 is coded for the OLT platform you name and verified before shipping. Validation is per OLT model, line card and software release, so test samples on your equipment before a volume order.

Request a quote for WTXGSPON-OLT-N1-20.

Send the host model and software release, quantity and coding needs. We reply with a matched P/N and sample plan.

Email waley@wincoteknetwork.com · WhatsApp / phone +86 176 8896 6828

WhatsApp