Home/Optical transceivers/GPON OLT SFP C+++

WincoTek GPON OLT SFP Class C+++ Transceiver(WTG02TC3)

WTG02TC3 is a GPON OLT SFP transceiver to ITU-T G.984.2 class C+++, for point-to-multipoint networks up to 20 km. It transmits 2.488 Gb/s continuously from a 1490 nm DFB laser at +6.5 to +10 dBm and receives 1.244 Gb/s upstream bursts at 1310 nm on an APD-TIA receiver rated −30 dBm. It is the highest-power optic in the WincoTek GPON OLT range, for large splits and long feeders.

WincoTek GPON OLT SFP C+++ GPON OLT transceiver
Class
C+++
Downstream
2.488 Gb/s, 1490 nm
Upstream
1.244 Gb/s, 1310 nm
Connector
SC
Key specifications

GPON OLT SFP C+++ at a glance.

Main optical, electrical and environmental values for WTG02TC3.

ParameterValue
Ordering codeWTG02TC3: GPON OLT SFP, class C+++, SC, 0 to 70 °C
StandardsITU-T G.984.2 class C+++; SFP MSA; SFF-8472; Telcordia GR-468-CORE
Data rateTX 2.488 Gb/s continuous; RX 1.244 Gb/s burst
Transmitter1490 nm DFB (1480–1500 nm); average output power +6.5 to +10 dBm, 8 dBm typ.; extinction ratio 8.2 dB min.
Receiver1310 nm (1260–1360 nm) burst-mode APD-TIA; fast burst packet detect; burst RSSI
RX sensitivity−30 dBm
RX saturation−10 dBm; receiver damage threshold 4 dBm
LOSAssert −45 dBm min.; de-assert −30 dBm max.
ReachUp to 20 km, subject to ODN design and optical budget
ConnectorSC receptacle, single fiber
Supply3.135 to 3.465 V; total supply current 400 mA max.
Case temperature0 to 70 °C
DDMYes, SFF-8472 memory map: temperature, voltage, bias, TX and RX power, with alarm and warning thresholds
Laser safetyClass I, IEC 60825

Main values for WTG02TC3. Full WincoTek datasheet: DatasheetPDF

Short links and testing. The receiver saturates at −10 dBm. With an ONU close to the OLT on a small split, or in lab tests, check the received upstream power and add attenuation so it stays between −30 and −10 dBm.
Typical applications

Where it is used.

From the datasheet application list and common network use.

  • GPON OLT line cards for FTTH and FTTB
  • ODNs with large splits or long feeders where class B+ or C+ runs short of budget
  • Raising the optical class of existing OLT ports without changing the ODN
  • Carrier and ISP access networks
Selection notes

Pick the class from the ODN.

Split ratio and reach decide, not the biggest number on the label.

GPON OLT optics come in classes. WincoTek offers B+ (WTG02TB1), C+ (WTG02TC1), C++ (WTG02TC2) and C+++ (WTG02TC3), with typical launch power rising from 3.5 to 8 dBm. A higher class buys loss budget for bigger splits and longer feeders at a higher module cost, so size it from the ODN rather than by default.

Work the budget upstream as well as downstream: ONU launch power minus fiber, splitter, connector and splice losses and at least 3 dB of margin must stay above −30 dBm at this receiver. A 1×64 P-grade splitter alone takes up to 20.2 dB, plus 0.3 dB for each connector in the path.

The receiver also has a ceiling of −10 dBm, so a C+++ optic may need attenuation on small splits near the OLT. Splitters, drop cable and pre-terminated cabling are on the FTTx page, and our ODN guide works through an example.

How it compares

Related WincoTek models.

The WincoTek GPON OLT SFP range. TX power values are typical, as in the transceivers table; sensitivity is from each datasheet.

ModelClassPackage / interfaceTypical TX powerRX sensitivity
WTG02TB1
DatasheetPDF
B+SFP, SC/UPC3.5 dBm−28 dBm
WTG02TC1
DatasheetPDF
C+SFP, SC/UPC5 dBm−30 dBm
WTG02TC2
DatasheetPDF
C++SFP, SC/UPC7 dBm−30 dBm
WTG02TC3
this page
DatasheetPDF
C+++SFP, SC8 dBm−30 dBm

Full range and all datasheets: optical transceivers. Guide: Pre-terminated ODN for FTTH deployments.

Coding, quality, warranty

Coded to your host, tested first.

Coding on request, validated per host model and software release.

Coding & compatibility

WTG02TC3 is coded for the OLT platform and line card you name. We read and back up the module data, write the approved profile, then read back and verify it with DDM. Compatibility is validated per OLT model, line card and software release, so we recommend testing samples on your equipment, with the ONUs you plan to use, before a volume order.

Quality & warranty

Built in ISO 9001-certified manufacturing partners. CE, RoHS, FCC and TÜV test reports are available for each model on request.

Warranty: hardware 3 years, software 1 year.

FAQ

Questions on this model.

Not answered here? Email waley@wincoteknetwork.com or message us on WhatsApp.

What does class C+++ mean for WTG02TC3?

It is the highest optical class in the WincoTek GPON OLT range: 1490 nm launch power of +6.5 to +10 dBm (8 dBm typical) and −30 dBm upstream sensitivity, to ITU-T G.984.2 class C+++.

When should I choose C+++ over B+ or C+?

When the ODN loss of a large split or a long feeder exceeds what the lower classes cover. On smaller splits a B+ or C+ optic is usually enough and costs less; size it from the loss budget.

Which connector does it use?

An SC receptacle on a single fiber. Downstream 1490 nm and upstream 1310 nm share the fiber.

Does it report diagnostics?

Yes. It follows the SFF-8472 memory map with temperature, voltage, bias, TX power and RX power, plus alarm and warning thresholds.

Can WTG02TC3 be coded for our OLT?

Yes. WTG02TC3 is coded for the OLT platform you name and verified before shipping. Validation is per OLT model, line card and software release, so test samples on your equipment before a volume order.

Request a quote for WTG02TC3.

Send the host model and software release, quantity and coding needs. We reply with a matched P/N and sample plan.

Email waley@wincoteknetwork.com · WhatsApp / phone +86 176 8896 6828

WhatsApp