Home/Optical transceivers/10G SFP+ BiDi 60 km

WincoTek 10G SFP+ BiDi 60 km Transceiver(WTS10E6B23(32)-K60C(I))

WTS10E6B23(32)-K60C(I) is a 10G SFP+ BiDi transceiver pair for full-duplex links up to 60 km over one single-mode fiber. WTS10E6B23 transmits 1270 nm and receives 1330 nm; WTS10E6B32 transmits 1330 nm and receives 1270 nm, with an APD receiver rated −20 dBm. It suits 10G Ethernet, Fibre Channel and CPRI links over longer single-fiber spans.

WincoTek 10G SFP+ BiDi 60 km transceiver
Data rate
Up to 11.3 Gb/s
Reach
60 km SMF
Receiver
APD
Connector
LC
Key specifications

10G SFP+ BiDi 60 km at a glance.

Main optical, electrical and environmental values for WTS10E6B23(32)-K60C(I).

ParameterValue
Ordering codesWTS10E6B23-K60C / -K60I (TX 1270 nm); WTS10E6B32-K60C / -K60I (TX 1330 nm)
Data rateUp to 11.3 Gb/s data links; 10.3125 Gb/s ordering rate
Applications (datasheet)10GBASE-ER/EW 10G Ethernet; 1/2/4/8/10G Fibre Channel; CPRI rates 0.614 to 10.138 Gb/s
Wavelengths (TX / RX)B23: TX 1270 nm, RX 1330 nm · B32: TX 1330 nm, RX 1270 nm (each 1260–1280 / 1320–1340 nm)
Laser / receiver1270 nm / 1330 nm DFB transmitter; APD/TIA receiver
TX power (avg.)0 to 5 dBm
RX sensitivity (avg.)−20 dBm
RX saturation−6 dBm
Reach60 km on 9/125 µm single-mode fiber
ConnectorLC receptacle, single fiber
SupplySingle +3.3 V; supply current 450 mA max.
Case temperature0 to 70 °C (-K60C); −40 to 85 °C (-K60I)
DDMYes, SFF-8472
Form factorHot-pluggable SFP+
EnvironmentalRoHS compliant and lead-free

Main values for WTS10E6B23(32)-K60C(I). Full WincoTek datasheet: DatasheetPDF

Short links and testing. The APD receiver saturates at −6 dBm, while the transmitter launches 0 to 5 dBm. On short spans and in loop-back tests, check RX power in DDM and add an LC attenuator so the received level stays between −20 and −6 dBm.
BiDi pairing

Used in pairs.

Each module transmits on one wavelength and receives on the other.

Order one of each.

A BiDi link sends and receives on one fiber, using two wavelengths. The two ends must be opposite halves of the same model, so order the modules as pairs in equal quantities.

WTS10E6B23-K60C(I)End A: TX 1270 nm / RX 1330 nm
← one SMF →
WTS10E6B32-K60C(I)End B: TX 1330 nm / RX 1270 nm

Choose C (0 to 70 °C) or I (−40 to 85 °C) for each end by site. Each end can be coded for a different host platform.

Typical applications

Where it is used.

From the datasheet application list and common network use.

  • 10G Ethernet over single-fiber spans up to 60 km
  • CPRI fronthaul on long single-fiber routes (CPRI rates listed in the datasheet)
  • 1G to 10G Fibre Channel extension
  • Regional access and aggregation rings where fiber pairs are limited
How it compares

Related WincoTek models.

All three use the same 1270/1330 nm pair on one LC fiber. The 60 km model switches to an APD receiver.

ModelReachReceiverTX power (avg.)RX sensitivityRX saturationSupply current (max.)
WTS10L2B23
DatasheetPDF
20 kmPIN/TIA−3 to 3 dBm−14.4 dBm0.5 dBm300 mA
WTS10E4B23
DatasheetPDF
40 kmPIN/TIA0 to 5 dBm−15 dBm0.5 dBm300 mA
WTS10E6B23(32)-K60C(I)
this page
DatasheetPDF
60 kmAPD/TIA0 to 5 dBm−20 dBm−6 dBm450 mA

Full range and all datasheets: optical transceivers.

Coding, quality, warranty

Coded to your host, tested first.

Host vendor names describe the target platform only.

Coding & compatibility

WTS10E6B23(32)-K60C(I) is coded for the host platform you name, for example Cisco, Juniper, Huawei, Arista, Nokia switches and routers. We read and back up the module data, write the approved profile, then read back and verify it with DDM. Compatibility is validated per host model and software release, so we recommend testing coded samples on your equipment before a volume order.

Quality & warranty

Built in ISO 9001-certified manufacturing partners. CE, RoHS, FCC and TÜV test reports are available for each model on request.

Warranty: hardware 3 years, software 1 year.

FAQ

Questions on this model.

Not answered here? Email waley@wincoteknetwork.com or message us on WhatsApp.

How is the BiDi pair made up?

One WTS10E6B23 (TX 1270 nm, RX 1330 nm) at one end and one WTS10E6B32 (TX 1330 nm, RX 1270 nm) at the other, on the same single-mode fiber.

How do I order?

Order equal quantities of WTS10E6B23 and WTS10E6B32, choose -K60C (0 to 70 °C) or -K60I (−40 to 85 °C), and name the host platform for each end.

Do I need an attenuator?

On short spans, yes. The APD receiver saturates at −6 dBm and the transmitter launches up to 5 dBm, so check RX power in DDM and attenuate to stay between −20 and −6 dBm.

How much power does it draw?

Supply current is 450 mA maximum from a single +3.3 V supply, per the datasheet.

Can it be coded for our host?

Yes. Each module is coded for the host platform you name and verified before shipping. Test coded samples first.

Request a quote for WTS10E6B23(32)-K60C(I).

Send the host model and software release, quantity and coding needs. We reply with a matched P/N and sample plan.

Email waley@wincoteknetwork.com · WhatsApp / phone +86 176 8896 6828

WhatsApp