WincoTek 800G OSFP SR8 100 m Transceiver(WTOS800-SR8-100C)

WTOS800-SR8-100C is an 800G OSFP SR8 transceiver for multimode links up to 60 m on OM3 or 100 m on OM4. Eight 850 nm VCSEL lanes at 53.125 GBd PAM4 are paired with eight PIN receivers, behind either one MPO-16 or two MPO-12 APC receptacles. Besides 800GBASE-SR8 it supports 400G, 200G and 100G modes, so one port can feed several lower-speed links.

WincoTek 800G OSFP SR8 transceiver
Data rate
800G (850 Gb/s)
Reach
60 m OM3 / 100 m OM4
Wavelength
850 nm
Connector
MPO-16 or 2× MPO-12 APC
Key specifications

800G OSFP SR8 at a glance.

Main optical, electrical and environmental values for WTOS800-SR8-100C.

ParameterValue
Ordering codesWTOS800-SR8-100C-MPO16 (one MPO-16 APC); WTOS800-SR8-100C-2MPO12 (two MPO-12 APC); both 0 to 70 °C, with DDM
Data rateUp to 850 Gb/s; 8 × 53.125 GBd PAM4; 800GAUI-8 electrical interface
Applications (datasheet)800GBASE-SR8, 400GBASE-SR8, 200GBASE-SR8, 8×100GBASE-SR1, 2×400GBASE-SR4, 4×200GBASE-SR2
StandardsOSFP MSA Rev 5.0
Wavelength840 to 860 nm
Laser / receiver8× VCSEL array, 8× PIN photodiode array
TX power, each lane (avg.)−4.6 to 4 dBm
RX sensitivity (OMAouter), each lane−4.6 dBm for TECQ ≤ 1.8 dB; −6.4 + TECQ for 1.8 < TECQ ≤ 4.4 dB
RX average receive power, each lane−6.4 to 4.0 dBm; damage threshold 5 dBm
Reach60 m on OM3, 100 m on OM4 multimode fiber
ConnectorMPO-16 (APC) or 2× MPO-12 (APC)
Power<14 W
Supply3.135 to 3.465 V
Case temperature0 to 70 °C
DDMYes

Main values for WTOS800-SR8-100C. Full WincoTek datasheet: DatasheetPDF

Typical applications

Where it is used.

From the datasheet application list and common network use.

  • 800G Ethernet links inside a row or pod on multimode fiber
  • Server and GPU node connections in AI and data center halls
  • Split one 800G port into 2 × 400G SR4, 4 × 200G SR2 or 8 × 100G SR1 links
  • Top-of-rack to leaf links up to 100 m on OM4
Selection notes

Multimode, measured first.

Fiber grade, connector version and breakout mode decide the order.

OM3 and OM4 share the same 50/125 µm core and aqua jacket, but OM4 has more than twice the modal bandwidth at 850 nm. For this module that means 60 m on OM3 and 100 m on OM4, so measure the longest run before choosing the cabling grade.

Pick the connector version to match the patch field: the -MPO16 version uses one 16-fiber MPO, the -2MPO12 version two 12-fiber MPOs. Both are APC, so trunks and cords need angle-polished ends.

Breakout modes let one OSFP port serve lower-speed neighbours: two 400G SR4, four 200G SR2 or eight 100G SR1 links. The far-end optics must use the matching multimode standard.

How it compares

Related WincoTek models.

800G OSFP options. The 100 m SR8 trades a little power for reach against the 50 m version; 2xDR4 covers single-mode up to 500 m.

ModelTypeFiber / reachWavelengthConnectorMax. power
WTOS800-2DR4-500C
DatasheetPDF
800G 2×DR4 (8×100G DR breakout)SMF, 500 m1310 nm2× MPO-12 (APC)<16.5 W
WTOS800-SR8-100C
this page
DatasheetPDF
800G SR8MMF, 60 m OM3 / 100 m OM4850 nm2× MPO-12 / MPO-16 (APC)<14 W
WTOS800-SR8-50C
DatasheetPDF
800G SR8MMF, 30 m OM3 / 50 m OM4850 nm2× MPO-12 (APC)<17 W
WTOS400-DR4-500C-CM
DatasheetPDF
400G OSFP DR4SMF, 500 m1310 nmMPO-12 (APC)<10 W

Full range and all datasheets: optical transceivers.

Coding, quality, warranty

Coded to your host, tested first.

Host vendor names describe the target platform only.

Coding & compatibility

WTOS800-SR8-100C is coded for the host platform you name, for example Cisco, Juniper, Huawei, Arista, Nokia switches and routers. We read and back up the module data, write the approved profile, then read back and verify it with DDM. Compatibility is validated per host model and software release, so we recommend testing coded samples on your equipment before a volume order.

Quality & warranty

Built in ISO 9001-certified manufacturing partners. CE, RoHS, FCC and TÜV test reports are available for each model on request.

Warranty: hardware 3 years, software 1 year.

FAQ

Questions on this model.

Not answered here? Email waley@wincoteknetwork.com or message us on WhatsApp.

What is the difference between WTOS800-SR8-100C and WTOS800-SR8-50C?

Reach and power. The 100C version reaches 60 m on OM3 and 100 m on OM4 at under 14 W. The 50C version reaches 30 m on OM3 and 50 m on OM4 at under 17 W.

Which connector version should I order?

WTOS800-SR8-100C-MPO16 has one MPO-16 APC receptacle; WTOS800-SR8-100C-2MPO12 has two MPO-12 APC receptacles. Choose the one that matches your trunks and cassettes.

Which breakout modes are supported?

The datasheet lists 800GBASE-SR8, 400GBASE-SR8, 200GBASE-SR8, 8×100GBASE-SR1, 2×400GBASE-SR4 and 4×200GBASE-SR2.

Will it work on OM5 fiber?

The datasheet specifies reach on OM3 and OM4 only. OM5 is designed for 850 nm as well, but ask us before planning links on OM5.

Can WTOS800-SR8-100C be coded for our switches?

Yes. WTOS800-SR8-100C is coded for the host platform you name, then read back and verified. Compatibility is validated per host model and software release, so test coded samples before a volume order.

Request a quote for WTOS800-SR8-100C.

Send the host model and software release, quantity and coding needs. We reply with a matched P/N and sample plan.

Email waley@wincoteknetwork.com · WhatsApp / phone +86 176 8896 6828

WhatsApp