Home/Optical transceivers/25G SFP28 BiDi 20 km

WincoTek 25G SFP28 BiDi 20 km Transceiver(WTS25L2B23)

WTS25L2B23 is a 25G SFP28 BiDi transceiver for full-duplex links up to 20 km over one single-mode fiber. It is used in pairs: WTS25L2B23 transmits 1270 nm and receives 1330 nm, WTS25L2B32 transmits 1330 nm and receives 1270 nm. A DML laser, a PIN receiver and internal CDRs serve 25G Ethernet and CPRI option 10 / eCPRI fronthaul at under 1.2 W.

WincoTek 25G SFP28 BiDi 20 km transceiver
Data rate
24.33–25.78 Gb/s
Reach
20 km SMF
Fiber
1 fiber, BiDi
Connector
LC
Key specifications

25G SFP28 BiDi 20 km at a glance.

Main optical, electrical and environmental values for WTS25L2B23.

ParameterValue
Ordering codesWTS25L2B23C / WTS25L2B23I (TX 1270 / RX 1330 nm); WTS25L2B32C / WTS25L2B32I (TX 1330 / RX 1270 nm); C = 0 to 70 °C, I = −40 to 85 °C
Data rate24.33 to 25.78 Gb/s
Applications (datasheet)25GBASE-LR Ethernet; CPRI option 10 / eCPRI
StandardsSFP28 MSA; SFF-8431; SFF-8432; SFF-8472
Wavelengths (TX / RX)B23: TX 1270 nm (1260–1280), RX 1330 nm · B32: TX 1330 nm (1320–1340), RX 1270 nm
Laser / receiverDML laser; PIN photodiode with TIA; internal CDR on transmit and receive (rate select RS0 / RS1)
TX power (avg.)−2 to 4 dBm; extinction ratio 3.5 dB min.; SMSR 30 dB min.
RX sensitivity (OMA)−12 dBm
RX overload (OMA)2 dBm
LOSAssert −30 dBm min.; de-assert −17 dBm max.
ReachUp to 20 km on single-mode fiber (specified at BER 5 × 10−5)
ConnectorLC, single fiber
Power<1.2 W; single +3.3 V ±5% supply
Case temperature0 to 70 °C (C); −40 to 85 °C (I)
DDMYes, SFF-8472: temperature ±3 °C, voltage ±3%, bias ±10%, TX and RX power ±3 dB
EnvironmentalRoHS compliant; class I laser

Main values for WTS25L2B23. Full WincoTek datasheet: DatasheetPDF

Short links and testing. The transmitter launches up to 4 dBm while receiver overload is 2 dBm (OMA). In loop-back tests and on very short links, read RX power in DDM and attenuate if needed.
BiDi pairing

Used in pairs.

Each module transmits on one wavelength and receives on the other.

Order one of each.

A BiDi link sends and receives on one fiber, using two wavelengths. The two ends must be opposite halves of the same model, so order the modules as pairs in equal quantities.

WTS25L2B23-C(I)End A: TX 1270 nm / RX 1330 nm
← one SMF →
WTS25L2B32-C(I)End B: TX 1330 nm / RX 1270 nm

Choose C (0 to 70 °C) or I (−40 to 85 °C) for each end by site. Each end can be coded for a different host platform.

Typical applications

Where it is used.

From the datasheet application list and common network use.

  • 5G fronthaul between radio units and DU or baseband sites (CPRI option 10 / eCPRI)
  • 25G Ethernet over one fiber up to 20 km
  • Server and switch uplinks where fiber pairs are short
  • Outdoor radio sites with the industrial grade
Selection notes

25G on one fiber for fronthaul.

Pairs, sites and temperature.

In fronthaul every radio sector needs a link with an optic at both ends, so an ordinary three-sector site uses six 25G modules. A BiDi pair halves the fiber each link needs, which adds up on routes that serve many radio sites.

Optics at the radio end often sit outdoors. The temperature rating is case temperature, not air temperature, so choose the I grade (−40 to 85 °C) for outdoor and unconditioned cabinets, and trend DDM temperature after installation.

Order B23 and B32 halves in equal quantities and label each end. For 10 or 40 km there are sibling BiDi models in the table below; with a fiber pair free, the duplex 25G SFP28 LR reaches 20 km.

How it compares

Related WincoTek models.

The 25G SFP28 BiDi family plus the duplex LR. Order matching halves of one model for both ends.

ModelTypeWavelengthsReachMax. power
WTSP-B2733(3327)-10D(I)
DatasheetPDF
25G SFP28 BiDi (pair)1270–1330 nm10 km<1.2 W
WTS25L2B23
this page
DatasheetPDF
25G SFP28 BiDi (pair)1270 / 1330 nm20 km<1.2 W
WTSP-B2733(3327)-40D(I)
DatasheetPDF
25G SFP28 BiDi (pair)1270–1330 nm40 km<1.5 W
WTSP-B2731(3127)-40D(I)
DatasheetPDF
25G SFP28 BiDi (pair)1270–1310 nm40 km<1.5 W
WTS25L2D(I)
DatasheetPDF
25G SFP28 LR, duplex1310 nm20 km<1.2 W

Full range and all datasheets: optical transceivers.

Coding, quality, warranty

Coded to your host, tested first.

Host vendor names describe the target platform only.

Coding & compatibility

WTS25L2B23 is coded for the host platform you name, for example Cisco, Juniper, Huawei, Arista, Nokia switches and routers. We read and back up the module data, write the approved profile, then read back and verify it with DDM. Compatibility is validated per host model and software release, so we recommend testing coded samples on your equipment before a volume order.

Quality & warranty

Built in ISO 9001-certified manufacturing partners. CE, RoHS, FCC and TÜV test reports are available for each model on request.

Warranty: hardware 3 years, software 1 year.

FAQ

Questions on this model.

Not answered here? Email waley@wincoteknetwork.com or message us on WhatsApp.

How is the BiDi pair made up?

One WTS25L2B23 (TX 1270 nm, RX 1330 nm) at one end and one WTS25L2B32 (TX 1330 nm, RX 1270 nm) at the other, on the same single-mode fiber.

Is it suitable for 5G fronthaul?

Yes. The datasheet lists CPRI option 10 and eCPRI as well as 25GBASE-LR Ethernet. Choose the industrial grade for outdoor radio sites.

What optical values does the datasheet give?

Average TX power −2 to 4 dBm, receiver sensitivity −12 dBm (OMA) and overload 2 dBm (OMA), at under 1.2 W.

Which temperature grades exist?

C versions for 0 to 70 °C and I versions for −40 to 85 °C case temperature, for both halves.

Can WTS25L2B23 be coded for our switches?

Yes. WTS25L2B23 is coded for the host platform you name, then read back and verified. Compatibility is validated per host model and software release, so test coded samples before a volume order.

Request a quote for WTS25L2B23.

Send the host model and software release, quantity and coding needs. We reply with a matched P/N and sample plan.

Email waley@wincoteknetwork.com · WhatsApp / phone +86 176 8896 6828

WhatsApp