Home/Optical transceivers/10G SFP+ DWDM tunable

WincoTek 10G SFP+ Tunable DWDM 80 km Transceiver(WTS10Z8DTx)

WTS10Z8DTx is a 10G SFP+ DWDM transceiver tunable to 96 channels across the C-band on the ITU 50 GHz grid, for links up to 80 km. It uses a negative-chirp integrated laser Mach-Zehnder (ILMZ) transmitter and an APD receiver, with tuning by wavelength or frequency through the SFF-8690 memory map. One part number covers every channel of a DWDM plan.

WincoTek 10G SFP+ DWDM tunable transceiver
Data rate
9.95–11.3 Gb/s
Reach
80 km SMF
Channels
96 at 50 GHz
Receiver
APD
Key specifications

10G SFP+ DWDM tunable at a glance.

Main optical, electrical and environmental values for WTS10Z8DTx.

ParameterValue
Ordering codesWTS10Z8DTC (0 to 70 °C), WTS10Z8DTE (−5 to 85 °C), WTS10Z8DTI (−40 to 85 °C); 10.3 Gb/s, DWDM ITU channel, 80 km SMF
Data rate9.95 to 11.3 Gb/s NRZ
Applications (datasheet)10G Ethernet; data center and Fibre Channel
Tuning191.35 to 196.10 THz, 96 channels on the 50 GHz grid; frequency accuracy ±2.5 GHz; tuning 10 s max. from any channel to any other
Laser / receiverILMZ (integrated laser Mach-Zehnder) TOSA, negative chirp; APD receiver with limiting amplifier
TX power−1.0 to +3.0 dBm (EOL); extinction ratio 9 dB min.; SMSR 35 dB min.
RX sensitivity−24 dBm back-to-back; −21 dBm with −300 to +1400 ps/nm dispersion (10.709 Gb/s, BER 10−12, OSNR > 35 dB)
RX overload−7 dBm; RX input wavelength 1525 to 1575 nm
Reach80 km on single-mode fiber
ConnectorDuplex LC
StandardsSFF-8431, SFF-8432, SFF-8690 (tunable SFP+ memory map)
Form factorSFP+, 56.5 × 13.9 × 11.85 mm, 20-pin; +3.3 V supply
DDMYes: temperature, laser bias, TX power, RX power, supply voltage, with alarm and warning flags

Main values for WTS10Z8DTx. Full WincoTek datasheet: DatasheetPDF

Short links and testing. The transmitter launches up to +3 dBm and the APD receiver overloads at −7 dBm. On short spans and in loop-back tests, check RX power in DDM and attenuate so the received level stays between the sensitivity and −7 dBm.
Typical applications

Where it is used.

From the datasheet application list and common network use.

  • 10G Ethernet over DWDM metro and access rings
  • Sparing: one tunable part instead of a stock for every fixed channel
  • Fibre Channel and data center links over a DWDM system
  • Outdoor or uncooled sites with the E or I temperature grade
Selection notes

Tunable or fixed DWDM?

Channel plans, sparing and the host.

DWDM packs channels 0.8 nm (100 GHz) or 0.4 nm (50 GHz) apart in the C-band, so many 10G services share one fiber pair. A fixed-channel optic must match its multiplexer port exactly; a tunable one is set to that channel instead.

Tuning follows the SFF-8690 tunable SFP+ memory map. Check that your host can set the channel, or tell us the host model and target channels so we can agree the approach with samples.

Pick the temperature grade by where the module sits: commercial for cooled rooms, extended (−5 to 85 °C) or industrial (−40 to 85 °C) for street cabinets. The rating is case temperature, which DDM reports in real time.

How it compares

Related WincoTek models.

10G long-reach options. Tunable DWDM covers every 50 GHz channel with one part; CWDM is the lower-cost choice for up to 8 long-reach channels.

ModelTypeWavelengthReceiverReach
WTS10Z8DTx
this page
DatasheetPDF
10G SFP+ DWDM tunableC-band, 96 channels at 50 GHzAPD80 km
WTS10Z8Dx
DatasheetPDF
10G SFP+ DWDM (fixed channel)C-bandPIN / APD80 km
WTS10Z8CxN1
DatasheetPDF
10G SFP+ CWDM1470–1610 nmAPD80 km
WTS10E4CxN1
DatasheetPDF
10G SFP+ CWDM1470–1610 nmPIN / APD40 km
WTS10Z8D
DatasheetPDF
10G SFP+ ZR1550–1565 nmAPD80 km

Full range and all datasheets: optical transceivers. Guide: DWDM vs CWDM for metro networks.

Coding, quality, warranty

Coded to your host, tested first.

Host vendor names describe the target platform only.

Coding & compatibility

WTS10Z8DTx is coded for the host platform you name, for example Cisco, Juniper, Huawei, Arista, Nokia switches and routers. We read and back up the module data, write the approved profile, then read back and verify it with DDM. Compatibility is validated per host model and software release, so we recommend testing coded samples on your equipment before a volume order.

Quality & warranty

Built in ISO 9001-certified manufacturing partners. CE, RoHS, FCC and TÜV test reports are available for each model on request.

Warranty: hardware 3 years, software 1 year.

FAQ

Questions on this model.

Not answered here? Email waley@wincoteknetwork.com or message us on WhatsApp.

How many channels can WTS10Z8DTx tune to?

96 channels on the ITU 50 GHz grid, from 191.35 to 196.10 THz, with ±2.5 GHz frequency accuracy.

How is the channel set?

Through the SFF-8690 tunable SFP+ memory map, by wavelength or frequency. Tuning from one channel to any other takes 10 s at most.

What receiver and sensitivity does it have?

An APD receiver: −24 dBm back-to-back, −21 dBm across −300 to +1400 ps/nm of dispersion, overload −7 dBm.

Which temperature grades exist?

WTS10Z8DTC 0 to 70 °C, WTS10Z8DTE −5 to 85 °C and WTS10Z8DTI −40 to 85 °C case temperature.

Can WTS10Z8DTx be coded for our switches?

Yes. WTS10Z8DTx is coded for the host platform you name, then read back and verified. Compatibility is validated per host model and software release, so test coded samples before a volume order.

Request a quote for WTS10Z8DTx.

Send the host model and software release, quantity and coding needs. We reply with a matched P/N and sample plan.

Email waley@wincoteknetwork.com · WhatsApp / phone +86 176 8896 6828

WhatsApp