Home/Optical transceivers/10G SFP+ CWDM 80 km

WincoTek 10G SFP+ CWDM 80 km Transceiver(WTS10Z8CxN1)

WTS10Z8CxN1 is a 10G SFP+ CWDM transceiver for links up to 80 km on single-mode fiber. It comes in eight ITU-T G.694.2 wavelengths from 1470 to 1610 nm, each with a CWDM EML laser and an APD receiver, on a duplex LC/UPC connector. Use it for 10GBASE-ER/EW, STM-64 and OC-192 links through passive CWDM multiplexers.

WincoTek 10G SFP+ CWDM 80 km transceiver
Data rate
Up to 11.3 Gb/s
Reach
80 km SMF
Wavelengths
1470–1610 nm, 8 ch.
Receiver
APD
Key specifications

10G SFP+ CWDM 80 km at a glance.

Main optical, electrical and environmental values for WTS10Z8CxN1.

ParameterValue
Ordering codesWTS10Z8CCN1 (0 to 70 °C), WTS10Z8CEN1 (−10 to 80 °C), WTS10Z8CHN1 (−40 to 85 °C); wavelength chosen from the selection table below
Wavelength codes47 = 1470 nm (gray), 49 = 1490 nm (violet), 51 = 1510 nm (blue), 53 = 1530 nm (green), 55 = 1550 nm (yellow), 57 = 1570 nm (orange), 59 = 1590 nm (red), 61 = 1610 nm (brown); clasp color in brackets
Data rateUp to 11.3 Gb/s; 10.3125 Gb/s ordering rate
Applications (datasheet)10GBASE-ER/EW 10G Ethernet; SDH STM-64; SONET OC-192
Laser / receiverCWDM EML transmitter; APD receiver with preamplifier
TX center wavelengthλ ±6.5 nm; spectral width 1 nm; SMSR 30 dB min.
TX power (avg.)−1 to 4 dBm; extinction ratio 8.2 dB; TDP 3.0 dB at 1450 ps/nm
RX sensitivity (avg.)−24 dBm
RX overload−8 dBm; damage threshold 5 dBm
ReachUp to 80 km on 9/125 µm single-mode fiber
ConnectorDuplex LC/UPC
Power2 W max.; supply current 577 mA
DDMYes, SFF-8472
EnvironmentalRoHS compliant and lead-free; metal enclosure

Main values for WTS10Z8CxN1. Full WincoTek datasheet: DatasheetPDF

Short links and testing. The transmitter launches up to 4 dBm and the APD receiver overloads at −8 dBm. On spans much shorter than 80 km and in loop-back tests, check RX power in DDM and attenuate so the received level stays between −24 and −8 dBm.
Typical applications

Where it is used.

From the datasheet application list and common network use.

  • 10G Ethernet over passive CWDM up to 80 km
  • SDH STM-64 and SONET OC-192 links
  • Carrier access and enterprise rings where an amplifier is not wanted
  • Outdoor cabinets with the extended or industrial grade
Selection notes

Long-reach CWDM, no amplifier.

Channel plan and loss budget for 40 to 80 km.

ITU-T G.694.2 defines 18 CWDM wavelengths from 1270 to 1610 nm, 20 nm apart. The last eight, 1470 to 1610 nm, are the ones generally used for spans over 40 km, which is exactly the set this module comes in.

Each multiplexer channel has a passband of about ±6.5 nm, and the transmitter must stay within it. Before pricing an amplifier, add up the losses: fiber, multiplexer and demultiplexer, any add/drop filters, connectors and splices, plus at least 3 dB of margin.

If the network will grow, choose a multiplexer with an express (pass-through) port, so another set of channels can be added later without replacing the first unit. For multiplexers see DWDM / OTN.

How it compares

Related WincoTek models.

10G long-reach options. CWDM is the lower-cost choice for up to eight long-reach channels; DWDM scales further.

ModelTypeWavelengthReceiverReach
WTS10Z8DTx
DatasheetPDF
10G SFP+ DWDM tunableC-band, 96 channels at 50 GHzAPD80 km
WTS10Z8Dx
DatasheetPDF
10G SFP+ DWDM (fixed channel)C-bandPIN / APD80 km
WTS10Z8CxN1
this page
DatasheetPDF
10G SFP+ CWDM1470–1610 nmAPD80 km
WTS10E4CxN1
DatasheetPDF
10G SFP+ CWDM1470–1610 nmPIN / APD40 km
WTS10Z8D
DatasheetPDF
10G SFP+ ZR1550–1565 nmAPD80 km

Full range and all datasheets: optical transceivers. Guide: DWDM vs CWDM for metro networks.

Coding, quality, warranty

Coded to your host, tested first.

Host vendor names describe the target platform only.

Coding & compatibility

WTS10Z8CxN1 is coded for the host platform you name, for example Cisco, Juniper, Huawei, Arista, Nokia switches and routers. We read and back up the module data, write the approved profile, then read back and verify it with DDM. Compatibility is validated per host model and software release, so we recommend testing coded samples on your equipment before a volume order.

Quality & warranty

Built in ISO 9001-certified manufacturing partners. CE, RoHS, FCC and TÜV test reports are available for each model on request.

Warranty: hardware 3 years, software 1 year.

FAQ

Questions on this model.

Not answered here? Email waley@wincoteknetwork.com or message us on WhatsApp.

Which wavelengths are available?

Eight: 1470, 1490, 1510, 1530, 1550, 1570, 1590 and 1610 nm, codes 47 to 61. The clasp color identifies each wavelength.

How do I order a specific wavelength?

Name the temperature grade (WTS10Z8CCN1, CEN1 or CHN1), the wavelength code (47 for 1470 nm up to 61 for 1610 nm) and the host platform. Each multiplexer channel needs its matching wavelength at both ends.

What are the optical levels?

Average TX power −1 to 4 dBm, receiver sensitivity −24 dBm and overload −8 dBm, per the datasheet.

Which temperature grades exist?

WTS10Z8CCN1 0 to 70 °C, WTS10Z8CEN1 −10 to 80 °C and WTS10Z8CHN1 −40 to 85 °C case temperature.

Can WTS10Z8CxN1 be coded for our switches?

Yes. WTS10Z8CxN1 is coded for the host platform you name, then read back and verified. Compatibility is validated per host model and software release, so test coded samples before a volume order.

Request a quote for WTS10Z8CxN1.

Send the host model and software release, quantity and coding needs. We reply with a matched P/N and sample plan.

Email waley@wincoteknetwork.com · WhatsApp / phone +86 176 8896 6828

WhatsApp